microMIND Installation Guide
microMIND Installation Guide Disclaimer All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems - without the written permission of the publisher. Company and product names mentioned herein are registered or unregistered trademarks of their respective companies.
microMIND Installation & Configuration Publisher NT-ware Systemprogrammierung GmbH Symbols used in this manual: Technical Editors Marja Pals Lydia Abghay Publisher Elk e Witt NT-ware GmbH Thomas Systemprogrammierung Lemmer Team Coordinator Technical Authors Claudia Kleinek Thomas Lemmeremper Production NT-ware Systemprogrammierung GmbH Production NT-ware Systemprogrammierung GmbH Note Printer Wizard Important Note Settings Online link Advanced Configuration Advanced Printer Configuration
Table of Contents Foreword 0 1 Document Versioning Information 2 2 microMIND 4 2.1 Introduction 4 2.2 Scope of supply 6 2.3 Technical Specifications 6 2.4 FCC and IC Compliance Note 7 2.5 Installation 7 2.6 LED Status 8 2.7 Configuration 9 2.7.1 2.8 Configurable param .........................................................................................................................................................
II
Document Versioning Information 1
microMIND - Installation Guide Version: 1.0 Date: 16 August 2010 First Draw-up Date: 16.08.2010 Author: Thomas Lemmer Revision history: Version: Revision date: Reviewer: Final Review: 1.0 Holger Bauszus, Karl Vieth Holger Bauszus 16.08.2010 Technologies concerned: microMIND File name: microMIND_Installation_&_Configuration_V1-0.PDF Short Summary: This manual describes the features, the installation, and the configuration of the microMIND in detail.
microMIND 2
microMIND - Installation Guide 2.1 Introduction The microMIND provides the possibility to add a MiCard (V2) reader as a Secure Print solution for any printer. Thus allowing you to turn your normal office printer into a cost effective secure print solution. No matter if this printer is a USB, a network printer or a printer with a different connection. The microMIND supports both, MiCard V1 (deprecated former version of the MiCard) and MiCard V2 readers.
microMIND - Installation Guide microMIND attached to a USB printer microMIND attached to a network printer 5
microMIND - Installation Guide 2.2 Scope of supply The microMIND package includes the microMIND device a short patch cable to connect the device to a printer Power supply (if no PoE microMIND) a Quick Installation Guide 2.3 Technical Specifications Power Supply: The microMIND is available in two different versions. One with PoE (Power over Ethernet) and one without.
microMIND - Installation Guide Important Note: Changes and/or modifications of the microMIND not approved by NT-ware Systemprogrammierung GmbH will make void the user’s authority to operate the microMIND. 2.4 FCC and IC Compliance Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
microMIND - Installation Guide 2. If it is a network printer, disconnect the device from the network. 3. If it is a network printer, plug-in the printers network cable in one of the RJ45 input jacks. 4. Attach the MiCard (V2) reader to the microMIND's USB port. 5. Attach the microMIND reader to the network. 6. Plug-in the power supply of the microMIND if required. This is necessary if you have no PoE microMIND or if you have a PoE microMIND but your network doesn't support PoE. 7.
microMIND - Installation Guide Status/Color Status description Orange A card has been detected by the MiCard (V2) reader and the uniFLOW server has been informed about it. This status is shown for approx. 2 seconds. Afterwards the LED turns green again. It also lights up in orange during the boot loader phase. Orange flashing A not supported USB card reader has been connected. Note that only MiCard (V2) readers are supported by the microMIND.
microMIND - Installation Guide The microMINDs IP configuration can be found by selecting a microMIND via mouse click on the IP address. You’ll find the serial number of the respective microMIND on a sticker on the back of the microMIND. A browser screen will open to configure the microMINDs IP address. By default the microMIND is set to DHCP, meaning that the microMIND receives it's configuration from the companies DHCP server if available.
microMIND - Installation Guide Update process: Format your USB stick according to the requirements listed above. Copy the MMAPP file onto the USB stick. Detach your microMIND from the power supply. If PoE is used, detach the network connection. Attach the USB stick to the microMIND. Attach the power supply. If PoE is used, attach the network connection. Update proceedure: LED Status: 1. The device starts with the boot loader phase.
©2010 MiCard is a registered trademark of NT-ware Sy stemprogrammierung GmbH
