MultiSync User’s Manual Bedienerhandbuch Manual del usuario Manuel Utilisateur Manuale utente 00Cover_all.
00Cover_all.
TCO’99 l English TCO'99 document. MultiSync Model Congratulations! You have just purchased a TCO’99 approved and labeled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Environmental Requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. In turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of flame retardant substances.
TCO’95 MultiSync Model Congratulations! You have just purchased a TCO’95 approved and labeled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also, to the further development of environmentally adapted electronics products.
Environmental Requirements Brominated flame retardants Brominated flame retardants are present in printed circuit boards, cables, wires, casings and housings. In turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of flame retardant substances.
Index Warning, Caution , Declaration......................................................................English-1 Contents.............................................................................................................English-2 Quick Start ....................................................................................................... English-3 Controls.............................................................................................................
English Deutsch Español Français Italiano 01b_English 7 2/26/02, 10:06 AM
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
English Contents Your new NEC MultiSync LCD monitor box* should contain the following: • MultiSync monitor with tilt base • Power Cord • Video Signal Cable (15-pin mini D-SUB male to DVI-A) • User’s Manual User’s Manual Power Cord Video Signal Cable (15-pin mini D-SUB male to DVI-A) * Remember to save your original box and packing material to transport or ship the monitor.
Quick Start To attach the MultiSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC or Mac with DVI digital output: Connect the DVI-D to DVI-D signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. For the PC with Analog output: Connect the 15-pin mini D-SUB to DVI-A signal cable to the connector of the display card in your system (Figure A.2).
English Macintosh Cable Adapter (not included) Macintosh G3 and G4 do not need a Macintosh cable adapter Figure B.1 Input1 Input2 Figure D.1 Power Cord Signal cable Press an arrow point “ ” portion with take off connector cover Connector Cover Power Cord (EU) Signal cable Figure C.1 Vacation Switch Power Button Figure E.
Tilt Grasp both sides of the monitor screen with your hands and adjust the tilt as desired. (Figure F.1). The movable scope for elevation and depression of LCD is -5°~30°angle. (Figure F.2). Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2. Place monitor face down on a non-abrasive surface (Place the screen on a 36 mm platform so that the stand is parallel with the surface.) (Figure G.1). 3.
English Figure G.2 Figure G.3 Figure G.4 Caution: Please use the attached screws (4pcs) when mounting. To fulfil the safety requirements the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor. The LCD monitor shall only be used with an approved arm (e.g. GS mark).
Controls OSM (On-Screen-Manager) Controls The OSM controls on the front of the monitor function as follows: To access OSM press any of the control buttons ( / , –, +). To change DVI/D-SUB signal input, press the NEXT button. Control Menu EXIT Exits the OSM controls. Exits to the OSM main menu. CONTROL / Moves the highlighted area left/right to select control menus. Moves the highlighted area up/down to select one of the controls.
Adjusts the horizontal size by increasing or decreasing this setting. Should the “AUTO Adjust function” do not give you a satisfactory picture setting, a further tuning can be performed using the “H.Size” function (dot clock). For this a Moiré test pattern could be used. This function may alter the width of the picture. Use left/Right Menu to center the image on the screen. If the H.Size is wrongly calibrated, the result would look like on the left drawing. The image should be homogeneous. When H.
Tools 1 SHARPNESS This function is digitally capable to keep crisp image at any timings. It is continuously adjustable to get distinct image or soft one as you prefer, and set independently by different timings. EXPANSION MODE Sets the zoom method. H-EXPANSION The horizontal image is expanded to approximately 2 times. V-EXPANSION The vertical image is changeable. DVI SELECTION This function selects EDID Data for ANALOG signal or DIGITAL signal on the DVI input.
Selecting Factory Preset allows you to reset all OSM control settings back to the factory settings. Individual settings can be reset by highlighting the control to be reset and pressing the RESET button. Information DISPLAY MODE Provides information about the current resolution display and technical data including the preset timing being used and the horizontal and vertical frequencies. Increases or decreases the current resolution. (Analog input only).
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC LCD COLOUR MONITOR: • • • • • • • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. Do not spill any liquids into the cabinet or use your monitor near water.
• • • • • • • • • • • • For optimum performance, allow 20 minutes for warm-up. Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. Position your monitor no closer than 40 cm and no further away than 70 cm from your eyes. The optimal distance is 58 cm. Rest your eyes periodically by focusing on an object at least 6 m away. Blink often.
Specifications Monitor Specifications (NL1502) MultiSync LCD Module 38 cm/15 inches 38 cm/15 inches 1024 x 768 Diagonal: Viewable Image Size: Native Resolution (Pixel Count): Input Signal Video: Sync: Display Colours Analog input: Synchronization Range Horizontal: Vertical: DVI Digital Input Monitor Notes Active matrix; thin film transistor (TFT) liquid crystal display (LCD); 0.297 mm dot pitch; 300cd/m2 white luminence, typical; 450:1 contrast ratio, typical DVI-I (TMDS) Separate sync.
English Features sRGB Colour Control: A new optimized colour management standard which allows for colour matching on computer displays and other peripherals. The sRGB, which is based on the calibrated colour space, allows for optimal colour representation and backward compatibility with other common colour standards. Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations.
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Check the Vacation Switch should be in the ON Position. Front power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.
• Use the OSM Image Adjust controls to increase or decrease the Coarse total. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) No Video • If no video is present on the screen, turn the Power button off and on again. • Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).
