Industrial 100/1000X to 10/100/1000T 802.
Table of Contents 1. Package Contents ................................................................................. 3 2. Product Specifications ........................................................................... 4 3. Hardware Introduction .......................................................................... 7 3.1 Three-View Diagram....................................................................... 7 3.2 LED Definition: ...................................................................
1. Package Contents Thank you for purchasing PLANET 10/100/1000T 802.3bt PoE++ Media IGUP-2205AT. In the following sections, Converter” means the IGUP-1205AT or compact industrial 100/1000X to Converter series, IGUP-1205AT and the term “Industrial PoE++ Media IGUP-2205AT. Open the box of the Industrial PoE++ Media Converter and carefully unpack it.
2. Product Specifications Model IGUP-1205AT IGUP-2205AT Hardware Specifications Copper Port 1 x 10/100/1000BASE-T 2 x 10/100/1000BASE-T SFP Slot 2 x 1000BASE-SX/LX/BX SFP interface Compatible with 100BASE-FX SFP Flow Control Back pressure for half duplex mode IEEE 802.
Enclosure IP30 metal case Installation DIN-rail kit and wall-mount ear ESD Protection 6KV DC Cables 10/100/1000BASE-T: 2-pair UTP Cat. 3, 4, 5, 5e, 6 (maximum 100 meters) EIA/TIA-568 100-ohm STP (maximum 100 meters) 100BASE-FX/1000BASE-SX/LX: Multi-mode: 50/125μm or 62.5/125μm optical fiber Single-mode: 9/125μm optical fiber Power Over Ethernet PoE Standard IEEE 802.3bt Power over Ethernet Plus Plus Backward compatible with IEEE 802.
Stability Testing IEC60068-2-32 (free fall) IEC60068-2-27 (shock) IEC60068-2-6 (vibration) Environment Temperature Operating: -40~75 degrees C Storage: -40~85 degrees C Humidity Operating: 5~90% (non-condensing) Storage: 5~90% (non-condensing) 6
Max. Fault Alarm Loading: 24V, 1A V1+ PWR1 Alarm PWR2 P2 Alarm IGUP-1205AT 1 DIN-Rail Kit Mounting Kit 50.00 [1.97] 107.00 [4.21] 18.00 [0.71] 38.90 [1.53] 87.80 [3.46] 97.10 [3.82] 135.00 [5.31] 56.00 [2.20] 7 Unit: mm 18.00 [0.71] Figure 1: IGUP-1205AT Three-View Diagram Mounting Kit 50.00 [1.97] Bottom View 9.20 [0.36] LNK ACT PoE-in-Use 48.80 [1.92] 802.3bt PoE++ 47.30 [1.86] Legacy Rear View 50.00 [1.97] 2 3 ACT ACT 30W 60W 90W Side View 40.00 [1.
163.00 [6.42] 28.00 [1.10] 50.00 [1.97] 18.00 [0.71] 50.00 [1.97] Rear View 107.00 [4.21] 18.00 [0.71] 48.80 [1.92] 38.90 [1.53] Side View 47.30 [1.86] 97.10 [3.82] 87.80 [3.46] PWR2 56.00 [2.20] Bottom View 1 802.3bt PoE++ IGUP-2205AT 2 LNK ACT PoE-in-Use 3 Legacy 4 ACT ACT P2 Alarm P1 Standard DC Input: 12-56V , 6A max. 60W 120W 180W Front View 50.00 [1.97] V2+ Alarm 8 PWR1 1000 LNK 100 LNK V1+ 135.00 [5.31] Side View Top View 9.20 [0.
Front View P1 P2 Alarm P1 30W 60W 90W 1000 LNK 100 LNK Standard P2 Alarm 60W 120W 180W ACT ACT 1000 LNK 100 LNK ACT ACT 3 4 2 3 Legacy Standard Legacy 2 LNK ACT PoE-in-Use LNK ACT PoE-in-Use 1 802.3bt PoE++ IGUP-1205AT 1 802.
3.2 LED Definition: System LED Color Function P1 Green Lights to indicate DC power input 1 has power. P2 Green Lights to indicate DC power input 2 has power. Alarm Red Lights to indicate that DC power has failed. PoE Usage Amber IGUP-1205AT (30W, 60W, 90W) Lights to indicate the system consumes over 30-/60/90-watt PoE power budget. Blinks to indicate the system consumes less than 30-/60-/90-watt PoE power budget.
■ Gigabit Fiber Interface LED Color Green Fiber LNK/ACT Amber Function Lights to indicate that the fiber optic port is successfully connecting to the network at 1000Mbps. Blinks to indicate the fiber optic port is receiving or sending data. Lights to indicate that the fiber optic port is successfully connecting to the network at 100Mbps. Blinks to indicate the fiber optic port is receiving or sending data. 3.
2. Tighten the wire-clamp screws for preventing the wires from loosening. 1 2 Power 1 + - 3 4 Alarm 5 6 Power 2 + - 1. The wire gauge for the terminal block should be in the range between 12 and 24 AWG. Note 2. The DC power input range is 12-56V DC. PWR1 and PWR2 must provide exactly the same DC voltage for power load balance while operating with dual power input. Caution 3.4 Wiring the Alarm Contact The alarm contacts are in the middle of the terminal block connector as the picture shows below.
1. The wire gauge for the terminal block should be in the range between 12 and 24 AWG. Note 2. Alarm relay circuit accepts up to 24V, max. 1A currents. 3.5 Grounding the Device Users MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device. EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY. Max. Fault Alarm Loading: 24V, 1A Earth Ground 1 2 3 4 5 6 V1+ PWR1 V2+ Alarm PWR2 DC Input: 12-56V , 6A max.
4. Hardware Installation This section describes the functionalities of the Industrial PoE++ Media Converter’s components and guides you to installing it on the DIN rail and wall. Please read this chapter completely before continuing. This following picture tells the user how to install the device, and the device is not IGUP-1205AT or IGUP-2205AT. Note 4.1 DIN-rail Mounting Installation 1 2 4.
Caution You must use the screws supplied with the wall-mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty.
5. Fiber and PoE Installation The IGUP-1205AT/IGUP-2205AT is flexible enough to extend the distance from 550m to 120km. It depends on the 1000BASE-X or 100BASE-FX SFP transceivers. The SFP transceivers are hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SFP port without having to power down the Industrial 802.3bt PoE++ Media Converter. If there is any IEEE 802.3af/IEEE 802.3at/IEEE 802.
Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team. PLANET online FAQs: http://www.planet.com.tw/en/support/faq.php Support team mail address: support@planet.com.tw Copyright © PLANET Technology Corp. 2022. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp.
