MODEL:NF-268 Your excellent helper in cable test! INSTRUCTION MANUAL RJ45/RJ11/BNC WIRE TRACKER ORIGINAL AUTHENTIC Patented products, rfeiting not allowed Counte REV1.
Brief Introduction The service manual for user here covers all products of NF-268 (all instructions are suitable for all products as shown in figure below unless there is another regulation): NF-268 1 2 POWER 3 NF-268 Anti-EI Wire Tracer STATUS 1 4 SCAN 6 8 SCAN 5 OFF 6 TEST 7 8 5 7 2 3 4 G OFF Anti-EI Wire Tracer VERIFY G SET Emitter Receiver Overview NF-268 is an updated item after NF-168.
Contents Product interface and keypad functions ......1 Operations .......................................................2 2.1 Cable tracing..................................................2 2.2 Cable mapping................................................2 Main Functions ................................................3 3.1 Trace STP/UTP network cable...........................3 3.2 Trace energized telephone cable.......................3 3.3 Trace monitoring cable connected to monitor......4 3.
1.
2.Operations 2.1 Cable tracing 2.1.1)Open battery cover, install DC 9V battery in launcher,push the key of emitter to “scan”, the indicator flashes, which means the emitter is normal. 2.1.2)Connect the cable to be tested to corresponding port. 2 . 1 . 3 )P u s h t h e k e y o f r e c e i v e r t o “ S c a n ” , t h e i n d i c a t o r f l a s h e s , which means the emitter is normal. Then hold the receiver to trace cable. During operation, users can alter the volume gradually to ideal state.
If more than 2 cables is disconnected, the corresponding leds won’t be on. If less than 2 cables is disconnected, all the leds won’t be on. If No.2 &No.3 is misorder, it will show as below Emitter: 1-2-3-4-5-6-7-8-G Receiver:1-3-2-4-5-6-7-8-G 3.Main functions 3.1 trace STP/UTP network cable (connected with exchanger or switch as below) Connect the network cable to be tested to RJ45 port. Push the key of receiver to “Scan”, the indicator flashes, which means the receiver is normal.
Connect the telephone cable to be tested to RJ11port. Then hold the receiver to locate the targeted cable as what 3.1 said. Note: in this case, users should alter the volume to degree 1-3 in order to find out targeted cable precisely. 3.3 trace monitoring cable (connected to monitor as below) Connect the telephone cable to be tested to RJ11port. Then hold the receiver to locate the targeted cable as what 3.1 said.
3.5 Check breakage location of non-energized wires (as below) Connect a broken wires with the two clips, push the key to “scan”, Keep the probe close to wire, it means normal if “beep” emits. Then move the probe along the wire, the point is breakage when no “beep” comes out. Note: 1) clip one core with red clamp, keep the black one free. 2)turn the volume to degree 6-8 when tracing cable. 3)Clip one core to tested. 3.6 Network cable mapping 3.6.1) If the tested cable is in good connection, No.
3.7 Unique function When users have targeted the network cable, at this time, he can directly insert the cable into RJ45 port of receiver to check its wiremap. If leds No.1-8 is on, it means the cable is normal. If not, the cable is abnormal. The details can be read from Chapter 3.6.
Specification: Item Specification Product name Power supply Wire tracker DC, 9V battery The max working current Signal transmission format ≤20mA Emitter ≤30mA Receiver Multi-frequency impulse Signal output electric status 8Vp-p Distance of signal transmission ≥3km Emitter Appearance dimension Weight (without batteries) 146×57×30 mm Receiver 187×46×27 mm Whole set 285×150×46 mm Emitter 0.08kg Receiver 0.08kg Whole set 0.16kg Packing list 7 1. Emitter 1PCS 6.
NF-306 NF-868 NF-8208 NF-801B NF-806R NF-816 NF-468L NF-3468 NF8108-M NF-388 NF-903 NF-906A Your excellent helper in cable test! 8
Your excellent helper in cable test! SHENZHEN NOYAFA ELECTRONIC CO.
