Installation Guide

ManualsBrandsNovolink ManualsLighting5 in. and 6 in. White Integrated LED Diffusion Recessed Trim with E26 Connector

Instructions for Installation

PACKAGING CONTENTS

(A) LED Module and Connector

(B) E26 Edison Screw Base Adapter

FOR USE WITH COMPATIBLE HOUSING MODELS:

Incandescent Housings - Commerical

Electric HBR5ICAT, HBR5, HBR5R, HALO

H5T, H5RT, H5ICT, H5RICAT, C7IC, C7ICR,

C7ICRA, C7, C7R, C7S, HBR5000SIC; HALO

H7ICT, H7RICT, H7ICAT, H7RICAT, H7T,

H7RT, H27ICT, H27T, H27RT, H750ICAT,

H750RICAT; CORDELIA X5LICAT, X5LICRAT,

HBR7LICAT, HBR7LICRAT; CAPRI CR1, CRRI;

DMF DH6ICATQ, DH6ICRATQ; ELCO EL5ICA,

EL5RICA; LITHONIA L5, L5R, EL7ICA, EL7RICA;

ELITE B5, B5R, B5IC, B5RIC, B6IC, B6RIC;

JUNO IC22, IC22R; LITHONIA L7X, L7XR;

NORA NHIC-17QAT, NHRIC-17QAT; PROGRESS

P187-TG, P87-AT,

P184-TG, P84-AT;

SEA GULL 11018,

11028; THOMAS

PS1, PS1-RM. HALO

LED HOUSINGS

- H550ICAT,

H550RICAT,

H750ICAT,

H750RICAT.

NRL56-12W-E26-W/D

5” and 6” Diffusion Recessed

LED Trim With E26 Connector

IMPORTANT SAFETY INSTRUCTIONS

When using product, basic precautions should

always be followed, including the following:

• Heed all warnings, including below warnings

and those included on product.

• Before attempting installation of any recessed

lighting luminaire check your local electrical

code. This code sets the wiring standards for

your locality and should be carefully studied

before starting.

WARNING

• Read and follow these instructions.

• Risk of ﬁre. MINIMUM 90º C Supply

conductors.

• Risk of ﬁre or Electric Shock: Please consult

an electrician for installation if uncertain of

luminaire electrical systems.

• Risk of electric shock. To avoid possible

electrical shock, be sure that power supply is

turned off at fuse box or circuit breaker before

installing or servicing ﬁxture.

• To prevent wiring damage or abrasion,

do not expose wiring to edges of sheet metal or

other sharp objects.

CAUTION

• Connect ﬁxture to a 120 volt, 60Hz power

source. Any other connection voids the

warranty.

• Fixture should be installed by persons with

experience in household wiring or by a

qualiﬁed electrician. The electrical system,

and the method of electrically connecting the

ﬁxture to it, must be in accordance with the

National Code and local building codes.

• Do not make or alter any open holes in an

enclosure of wiring or electrical components

during kit installation.

SAVE THESE INSTRUCTIONS

AND WARNINGS

COMPATIBLE HOUSING DIMENSIONS

Summary of content (2 pages)

PAGE 1
Instructions for Installation PACKAGING CONTENTS (A) LED Module and Connector NRL56-12W-E26-W/D 5” and 6” Diffusion Recessed LED Trim With E26 Connector IMPORTANT SAFETY INSTRUCTIONS When using product, basic precautions should always be followed, including the following: (B) E26 Edison Screw Base Adapter (C) Torsion Spring FOR USE WITH COMPATIBLE HOUSING MODELS: Incandescent Housings - Commerical Electric HBR5ICAT, HBR5, HBR5R, HALO H5T, H5RT, H5ICT, H5RICAT, C7IC, C7ICR, C7ICRA, C7, C7R, C7S, HBR500
PAGE 2
DETERMINING WHICH INSTALLATION METHOD TO USE 5. Squeeze the torsion springs together as shown and install into torsion spring brackets inside recessed housing. For 6” housings: Locate the torsion spring receiving brackets with bottom clip. Repeat for second bracket. 6. Carefully route wires into fixture and push module up flush to ceiling surface. For 5” housings: Locate the torsion spring receiving brackets with upper clip. Repeat for second bracket. 1-YEAR LIMITED WARRANTY INSTALLATION 1.