Adam Equipment PTS SERIES With AE402 Indicator (P.N.
Adam Equipment 2011 ©
Thank you for purchasing the ADAM PTS Pallet Truck. For your safety and correct operation, please read the following instructions carefully before using it. CONTENT 1.0 2.0 3.0 4.0 5.0 6.0 SAFETY ............................................................................................................................. 3 INSTRUCTION .................................................................................................................. 5 2.1 SPECIFICATIONS .....................................
2 Adam Equipment 2011 ©
1.0 SAFETY • To prevent damage to the scale, please read these operating instructions thoroughly. • When using the pallet truck, please keep the handle in the DRIVE position. • This pallet truck must be operated by trained personnel only.
4 Adam Equipment 2011 ©
2.0 INSTRUCTION 2.1 SPECIFICATIONS Common specifications Model PTS 2000 PTS 5000a Load cell Capacity 2000 kg 5000Lb Resolution 0.5 kg 1Lb Fork length 1150mm Fork Width (each) 160mm (6.3”) 160mm (6.3”) Fork Width (total) 540mm (21.25”) 680mm (26.77”) Fork Height 77mm increasing to 192mm 77mm increasing to 192mm (3” – 7.5”) (3” – 7.5”) 125 kg (275 Lb) 135 kg (297 Lb) Net Weight (45.
6 Adam Equipment 2011 ©
7 Adam Equipment 2011 ©
3.0 INSTALLATION Please follow the installation instructions to ensure correct operation of your PTS. In transportation the handle is removed from the truck, this needs to be installed following the instructions below: NOTE: Do not lower the handle down fully until completing the instructions below. 1) Insert the roller pin into the hole of roller rack, securing the handle to the frame. 2) Fit the split pin through the holes provided. 3) Pass the chain through the center hole of the roller pin.
9 Adam Equipment 2011 ©
3.
The Indicator bracket is fitted to the PTS using 4 x M4 screws as the picture below shows, these should be tightened using the Allen Key supplied . M4 x 6 Screws 4 places The Indicator cable goes through the hole on the bracket and connects to the Indicator using the 7 pin connector. 7 pin connector fitted here.
The AE 402 indicator is placed into the mounting bracket, and secured using the two plastic fasteners as shown below: Plastic fasteners used to secure Indicator to the bracket.
4.0 CALIBRATION The PTS is factory calibrated, please refer to the user manual for the indicator supplied (AE 402) when further calibration when required.
5.0 TROUBLE SHOOTING No. Problem Cause Solution Forks cannot ascend 1 2 3 4 5 to the maximum Inadequate hydraulic oil in the chamber. Refill oil chamber. See Figure 1. No hydraulic oil. Refill oil chamber. See Figure 1 . Oil is not clean. Change oil height Forks can not be raised Forks can not Position of the goods are to one side of the truck descend Relocate load. . Oil spillage Aging or damaged seals. Call for Service.
6.0 MAINTENANCE • Please check the oil every six months , we suggest you use hydraulic oil: ISO VG32 • Whilst in transit air may enter into the hydraulic pump, this may result in the forks not raising when first used. Please move the handle up and down several times to allow air to escape. • Routine maintenance is necessary. You should focus on the wheels and handle assemblies. When the truck is not in use, remove the items on the forks, and reset the forks to their lowest position.
16 Adam Equipment 2011 ©
Manufacturer’s Declaration of Conformity This product has been manufactured in accordance with the harmonised European standards, following the provisions of the below stated directives: Electro Magnetic Compatibility Directive 2004/108/EC Low Voltage Directive 2006/95/EC Adam Equipment Co. Ltd. Bond Avenue, Denbigh East Milton Keynes, MK1 1SW United Kingdom FCC COMPLIANCE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
ADAM EQUIPMENT is an ISO 9001:2008 certified global organisation with more than 30 years experience in the production and sale of electronic weighing equipment. Products are sold through a world wide distributor network supported from our company locations in the UK, USA, SOUTH AFRICA and AUSTRALIA. ADAM’s products are predominantly designed for the Laboratory, Educational, Medical and Industrial Segments.
