Adam Equipment LBK SERIES (P.N.
© Adam Equipment Company 2009
Easy Reference: Model name of the scale: Serial number of the unit: Software revision number (Displayed when power is first turned on): Date of Purchase: Name of the supplier and place: © Adam Equipment Company 2009
1 © Adam Equipment Company 2009
CONTENTS 1.0 INTRODUCTION............................................................................................ 4 2.0 SPECIFICATIONS ............................................................................................ 5 3.0 SAFETY PRECAUTIONS ................................................................................... 6 4.0 SET UP............................................................................................................ 6 4.1 ASSEMBLING OF SCALE........................
3 © Adam Equipment Company 2009
1.0 INTRODUCTION • The LBK models are supplied with a power cord in the case of LBK-a models a DC adapter, with all models also having rechargeable battery operation. • Four models: 3kg/6lb X 0.5g/0.001lb 6kg/12lb X 1g/0.002lb 12kg/25lb X 2g/0.005lb 30kg/65lb X 5g/0.
2.0 SPECIFICATIONS model LBK-3/6a LBK- 6/12a LBK-12/25a LBK-30/65a capacity 3Kg/6lb 6Kg/12lb 12Kg/25lb 30Kg/65lb Readability 0.5g/0.001lb 1g/0.002lb 2g/0.005lb 5g/0.01lb Resolution 1:6000 1:6000 1:6000 1:6000 Repeatability ± 0.5g/0.001lb 1g/0.002lb 2g/0.005lb 5g/0.01lb Linearity ± 1g/0.002lb 2g/0.004lb 4g/0.01lb 10g/0.
3.0 SAFETY PRECAUTIONS Caution: Please use only the original power cord or DC adapter supplied with the scale. Other cords or adapters may damage the scale. Notice: • Avoid extremes of temperature. Do not place in direct sunlight or near air conditioning vents. • Battery should be removed if the scale is not used for a long period of time. • Do not stack material on the scale when it is not in use. • Avoid high humidity that might cause condensation, and keep away from direct contact with water.
4.2 ASSEMBLING OF BATTERY AND POWER In some cases the rechargeable battery must be shipped separate from the scale. In this case the user must install the battery. Remove the battery cover under the scale and put the 6v 4Ah rechargeable battery provided in to the battery compartment. Connect the battery to the cable paying attention to the polarity. The red connector goes to the (+) positive terminal on the battery, the black connector goes to the (-) negative terminal on the battery.
5.0 WEIGHING 5.1 BEFORE WEIGHING Check the setting of the auto shut off function, see section 6.2. If the auto shut off function is on, the scale will shut off after a period of time if the scale is not used and it has a stable reading. 5.2 WEIGHING • Press [On/Off] to turn on the scale. The display will show “LBK-1.0 LBK” and show the current voltage “X.X vol” .Then it will begin it’s self checking test from 0 to 9. When the reading is stable, the display will show "0.
5.3 POUND/OUNCE MODE: When using the pounds/ounces weighing unit the display will show the results rounded to the nearest ounce. 5.4 Model Weight Display Readability specification LBK 3/6a LBK6/12a LBK12/25a LBK30/65a 5Lb15.98oz 11Lb15.9oz 24Lb15.9oz 64Lb15.8oz 5 15.98 11 15.9 24 15.9 64 15.8 Readability 0.02oz max capacity 6Lb Readability 0.1oz max capacity 12Lb Readability 0.1oz max capacity 25Lb Readability 0.
• If a container is used, place the empty container on the pan before entering parts counting mode then press [Tare] key to remove the weight of the empty container. Then press [Func] key to go to parts counting mode and select the preset sample piece value and add the items to the container as selected and press [Zero] key. • Press [Func] to exit and go back to the normal weighing mode. 5.4.
6.0 FUNCTION SETTING 6.1 ENTERING THE FUNCTION SETTING MODE • Press [On/Off] to shut off the power. • Hold [Tare] and press [On/Off] to turn the scale on. • The display will show “LBK-1.0 LBK” and then enter the auto shut off mode. • The display will show “OFF PWR” or “XX PWR” (XX is the number of minutes before the scale would shut off automatically if it has remained stable for the set amount of time). • Release the [Tare] key. 6.
6.4 PARTS COUNTING FUNCTION • • • • Press [Tare] to switch on or off the part counting function. "OFF PCS" :part counting function is off. "ON PCS" : part counting function is on. Press [Unit] key to confirm the setting and look through the next setting. It would enter the percentage weighing when it shows "On PEr " or "OFF PEr". 6.5 PERCENTAGE WEIGHING FUNCTION • • • • Press [Tare] key to switch on or off this function. "OFF PEr ":the percentage function is off. "ON PEr”: the percentage function if on.
6.7 SELECTION OF WEIGHING UNITS Each weighing unit can be set to be either on or off. If it is on it is available when the user presses the [Unit] key during normal weighing. If it is off the weighing unit is not available during normal use. The grams unit is always on. Press [Tare] key to change the unit from on to off. On: the unit is activated. Off: the unit is disabled. All the units will be in the following sequence: "Kg" / "lb" / "oz"/"Lb.Z". • Press [Unit] key to confirm and move to the next unit.
7.0 CALIBRATION • Calibration is recommended for best accuracy. It is suggested that the scale be calibrated when first installed and any time the scale is moved to a different environment. • To ensure best accuracy calibrate before use. • Ensure weights are ready before calibrating, the weight should be of a known accuracy, for example OIML class M1 or Class 4 of ASTM E617. • Do not calibrate the scale if no calibration weight is available.
Calibration selection values for all model: LBK 3/6a LBK 6/12a LBK 12/25a LBK 30/65a 1Kg/2kg/3kg 2Kg/4kg/6kg 4Kg/8kg/12kg 10Kg/20kg/30kg 2lb/4lb/6lb 4lb/8lb/12lb 10lb/20lb/25lb 20lb/40lb/60lb • Press [Zero] key, the display will show “Load” then add the selected calibration mass value to the pan. • After the calibration mass is added, wait for the stable symbol to come on and then press [Zero] key, the display will show “PASS”, and then return to normal weighing after 3 seconds.
Manufacturer’s Declaration of Conformity This product has been manufactured in accordance with the harmonised European standards, following the provisions of the below stated directives: Electro Magnetic Compatibility Directive 2004/108/EC Low Voltage Directive 2006/95/EC Adam Equipment Co. Ltd. Bond Avenue, Denbigh East Milton Keynes, MK1 1SW United Kingdom FCC COMPLIANCE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
ADAM EQUIPMENT is an ISO 9001:2000 certified global company with more than 35 years experience in the production and sale of electronic weighing equipment. Adam products are predominantly designed for the Laboratory, Educational, Medical, retail and Industrial Segments.
