User Manual
Table Of Contents
- _
- Foreword
- Introduction
- Section One: Simplex 4010 NION Hardware
- 1.1: General Description
- 1.2: Hardware Description
- Figure 1-1: NION-NPB Layout
- 1.3: SMX Network Connection
- Figure 1-2: SIMPLEX 4010 NION TB5 Power Connection
- 1.4: SMX Network Transceivers
- Figure 1-3: FTXC-PCA and FTXC-PCB Network Transceivers
- Figure 1-3a: FTXC-PCA Transceiver Wiring
- Figure 1-4: S7FTXC-PCA Style 7 Transceiver
- Figure 1-5: Sample Style-7 Networks
- Figure 1-6: FOXC-PCA and DFXC-PCA Fiber Optic Network Transceivers
- Section Two: Simplex 4010 NION Installation and Configuration
- 2.1: Simplex 4010 NION Connection
- Figure 2-1: Simplex 4010 NION Architecture
- Figure 2-2: Simplex 4010 NION to Simplex 4010-9811 Serial Connections
- 2.2: Simplex 4010 NION Enclosure and Mounting
- Figure 2-4: NISCAB-1 Enclosure Mounting Hole Layout
- 2.3 Event Reporting and Acknowledgement
- Figure 2-5: Installing the NION in a NISCAB-1
- Section Three: Simplex 4010 NION Explorer
- 3.1 Simplex Explorer Overview
- 3.2 Simplex 4010 Explorer Operation
- 3.2.1 Registering and Opening the Simplex Explorer
- 3.2.2 The Simplex 4010 Explorer Main Form
- 3.2.3 Configuring the NION through Simplex 4010 Explorer
- Figure 3-2: NION-Simplex 4010 Configuration Menu
- Figure 3-1: Simplex 4010 Explorer
- Figure 3-4: Duplicate Device Labels
- Figure 3-3: Learn Panel Devices Session
- Figure 3-5: Data Capture Mode
- Figure 3-6: NION Configuration Options
10
Simplex 4010 NION Installation/Operation Manual Version 2 Document 51998 Rev. A1 03/26/03
Figure 1-1: NION-NPB Layout
Service LED - Indicates binding status of node on Echelon network.
• Slow blink indicates NION not bound.
• Off indicates NION bound.
• On indicates nonrecoverable error.
Network Status - Indicates status of Echelon network interface.
• Slow blink indicates network operation normal.
• Off indicates network interface not functioning.
• Fast blink indicates a network communication error.
Network Packet - Blinks briefly each time a data packet is received or transmitted on the Echelon network.
Serial 2 - Application specific indicator of serial port activity (port 2).
Serial 1 - Application specific indicator of serial port activity (port 1).
NION Status - Indicates status of the NION.
• Rapid blinking indicates proper NION operation.
• On or Off indicates critical error and that the NION is not functioning.
Diagnostic LEDs
The NION contains six LEDs which are used as aids in diagnosing proper operation. The following paragraph
details the function of each LED.
ServiceService
ServiceService
Service
Network StatusNetwork Status
Network StatusNetwork Status
Network Status
Network PNetwork P
Network PNetwork P
Network P
acketacket
acketacket
acket
Serial 2Serial 2
Serial 2Serial 2
Serial 2
Serial 1Serial 1
Serial 1Serial 1
Serial 1
NION StatusNION Status
NION StatusNION Status
NION Status
3V Lithium3V Lithium
3V Lithium3V Lithium
3V Lithium
BatteryBattery
BatteryBattery
Battery
J1 Header for EchelonJ1 Header for Echelon
J1 Header for EchelonJ1 Header for Echelon
J1 Header for Echelon
Network TNetwork T
Network TNetwork T
Network T
ransceiverransceiver
ransceiverransceiver
ransceiver
Application PLCCApplication PLCC
Application PLCCApplication PLCC
Application PLCC
SW2 NetworkSW2 Network
SW2 NetworkSW2 Network
SW2 Network
Binding ButtonBinding Button
Binding ButtonBinding Button
Binding Button
SW1 ResetSW1 Reset
SW1 ResetSW1 Reset
SW1 Reset
ButtonButton
ButtonButton
Button
Network Communication PLCCNetwork Communication PLCC
Network Communication PLCCNetwork Communication PLCC
Network Communication PLCC
SMX TSMX T
SMX TSMX T
SMX T
ransceiverransceiver
ransceiverransceiver
ransceiver
Standoff MountingStandoff Mounting
Standoff MountingStandoff Mounting
Standoff Mounting
HolesHoles
HolesHoles
Holes
ChassisChassis
ChassisChassis
Chassis
GroundGround
GroundGround
Ground
Diagnostic LEDSDiagnostic LEDS
Diagnostic LEDSDiagnostic LEDS
Diagnostic LEDS
R72 Cut TR72 Cut T
R72 Cut TR72 Cut T
R72 Cut T
o Disable Groundo Disable Ground
o Disable Groundo Disable Ground
o Disable Ground
Fault DetectionFault Detection
Fault DetectionFault Detection
Fault Detection
GND +24VDC
PP
PP
P
ower Input (TB5)ower Input (TB5)
ower Input (TB5)ower Input (TB5)
ower Input (TB5)
TB6-Relay OutputTB6-Relay Output
TB6-Relay OutputTB6-Relay Output
TB6-Relay Output
U24U24
U24U24
U24
BT1BT1
BT1BT1
BT1
U6U6
U6U6
U6
TB7 - RS-485 InterfaceTB7 - RS-485 Interface
TB7 - RS-485 InterfaceTB7 - RS-485 Interface
TB7 - RS-485 Interface
NONO
NONO
NO
TETE
TETE
TE
: The NION-: The NION-
: The NION-: The NION-
: The NION-
Simplex 4010 does notSimplex 4010 does not
Simplex 4010 does notSimplex 4010 does not
Simplex 4010 does not
use this connection.use this connection.
use this connection.use this connection.
use this connection.
TB1- 5-TB1- 5-
TB1- 5-TB1- 5-
TB1- 5-
WW
WW
W
ire Serialire Serial
ire Serialire Serial
ire Serial
Interface AInterface A
Interface AInterface A
Interface A
RX
GND
CTS
RTS
TX
+5VDC
GND
RX+
RX-
TX+
TX-
NOTE: There is a paper insulator
between the battery and the
battery clip installed at the factory
to keep the battery charged.
Remove the insulator before
applying power.
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com