All products are trademarks of Nostalgia Products Group, LLC. Worldwide design & utility patented or patents pending. © 2011 Nostalgia Products Group, LLC. www.nostalgia electrics.com (rev.
SCC200 Vintage Collection™ Old Fashioned Snow Cone Cart Instructions and Recipes
CONTENTS IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 4 PARTS & ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . 5 HOW TO OPERATE . . . . . . . . . . . . . . . . . . . . . . . 10 HELPFUL TIPS . . . . . . . . . . . . . . . . . . . . . . . . . 11 CLEANING & MAINTENANCE . . . . . . . . . . . . . . . .
ENGLISH IMPORTANT PRECAUTIONS 1. NEVER immerse in water. 2. NEVER use near water. 3. NEVER use an abrasive sponge or cloth. 4. NEVER use a scouring pad on the appliance. 5. NEVER leave appliance unattended while in use. 6. NEVER try to force the cover in the locking mechanism. 7. Unplug unit from outlet when not in use and during cleaning. 8. DO NOT operate this appliance with a damaged cord or plug, or if the appliance ever malfunctions. 9.
to prevent injury due to tripping over cord. 12. Extreme caution must be used when moving this appliance. ENGLISH 13. DO NOT use the appliance for other than its intended use. 14. An appliance that is plugged into an outlet should not be left unattended while in operation. 15. Check Ice Hopper for presence of foreign objects prior to use. 16. Blades are extremely sharp. Use with extreme caution. 17.
ENGLISH PARTS & ASSEMBLY Please ensure that you have removed all of the hardware and parts listed before discarding packaging. In our efforts to reduce packaging, we maximize the packing material to protect your new purchase. As a result, small parts may not be readily visible. Hardware #1 Screw (8mm) Qty. 4 #5 Flat Washer Qty. 6 5 #2 Screw (8mm) Qty. 6 #6 Flat Washer Qty. 4 #3 Bolt (25mm) Qty. 4 #7 Nut Cap Qty. 6 #4 Bolt (60mm) Qty.
G-Wheel 1 2 1 C-Storage D-Lock K screw Cross barcompartent K-2Cross bar 1 Wrench 2 2 D-Lock screw HI--Base E1-Push support 1 E-Push handle L-1Leg assembly -Push handle J-Bottom Plate 1 L Leg Eassembly 1 1 F-Axle assembly bolt 4 F-Axle bolt K-Cross bar 1 2 F-Axle boltM-2Leg L-Leg assembly 1 G Wheel 2 G G-Wheel 2 M Leg Hassembly bolt 4 N-Knife disassembly tool -Whee 1 M-Leg assembly bolt 4 -Wrench 2 Wrench 2 H N Knife disassembly tool 1 H Wren BI-Base support 1 Parts A A B Plate1 N Knife disassembly tool 1I-B
Attach Push Handle (E) from inside Storage Compartment (B) using supplied #1 Screws. 2. Insert Cross Bar (K) into the square inserts on the inside of Base Support (I) and secure from below with two #2 Screws. Insert the Leg Assembly (L) over the protruding ends of the Base Support (I) and fasten from the inside of Base Support (I) using four #4 Bolts, four #5 Flat Washers, and four #6 Nut Caps. 3. Secure Bottom Plate (J) to Base Support (I) using four #2 Screws. 4.
2. Put on one #5 Flat Washer. Insert Axle Bolt (F) with Wheel (G) into Base Support (I). 3. Add a second #5 Flat Washer and #6 Nut Cap. Use Wrench (H) to tighten the #6 Nut Cap. 4. Repeat steps to attach second Wheel (G) onto the other side of the Base Support (I). (#6) Flat Washers ENGLISH Assembly of Wheels 1. Slide one #4 Flat Washer onto Axle Bolt (F) and insert Axle Bolt (F) into Wheel (G). (#7) Nut Cap (#5) Flat Washer (F) Axle Bolt (I) Base Support !"# "pdfFactory Pro" $#%&'( www.
ENGLISH Attaching Cone Dispenser 1. Screws have already been screwed into pre-drilled holes on the side of Main Unit (A). 2. Line up the two holes of Cone Dispenser (M) with the two screws and hang Cone Dispenser (M). Slide Cone Dispenser (M) down so that screws fit snugly in slots on Cone Dispenser (M). 3. Tighten screws, but do not overtighten.
HOW TO OPERATE ENGLISH ON / OFF & Light Switches Cone Dispenser Ice Hopper Door Handle Cone Holder Before first use, clean the inside of the unit by wiping with a moist, nonabrasive sponge, towel or cloth and then wipe with a non-abrasive dry towel. 1. First, find a flat surface near an electrical outlet before starting. Make sure your cord is away from any water source. It is acceptable to use an extension cord if needed. 2.
ENGLISH HELPFUL TIPS Ice For optimal ice shaving results, ice cubes should sit out of the freezer, in a bowl, for about 10 minutes before putting them into the shaving unit. If ice is frosty in appearance, it is too hard to shave. When ice is clear and wet to the touch, then it is ready to shave. CLEANING & MAINTENANCE 1. Make sure appliance is turned off and unplugged before cleaning. 2. Open the housing door to clean and dry the inside of the unit using a slightly damp, non-abrasive cloth or sponge.
Steps to Replace the Blade Remove the Ice Tray and insert the Disassembly Tool (C) over the three arms of the Spinner. 2. Once the Disassembly Tool (C) is properly inserted, twist counterclockwise (as the arrow shows) and lift the Spinner out. 3. Carefully press the tabs of the Blade Housing inward and lift up to release. 4. Twist off the Blade Cap and, using extreme caution, remove the Blade Cartridge. Insert the replacement Blade Cartridge, and reverse the above steps to reassemble.
ENGLISH RECIPES The OLD FASHIONED SNOW CART makes light, fluffy mounds of ice. Use your imagination with different fruits, syrups, sodas, teas, and juices to create any number of refreshing, icy, low-fat treats, drinks and desserts. Enjoy your shaved ice in a variety of ways. BOTTLED SYRUP CONCENTRATE • 19 Ounces of Warm Water Put 19 ounces of warm water into a one quart, or larger, bottle. • 2¾ Cups Sugar • 1-Quart Empty Bottle Using a funnel, add 2 ¾ cups of sugar to the water.
PEACH SPRITZER 2 Cups Peach Seltzer • 2 Tbsps. Freshly Squeezed Orange Juice • 1 Packet of Sugar Substitute Fill a cup halfway with freshly shaved ice. ENGLISH • Pour peach seltzer and orange juice over ice. Empty packet of sugar substitute into cup. Stir until well blended. Add additional ice if desired, until cup is full. Serves one. VANILLA SNOW • 3 Scoops of Vanilla Ice Cream • Shaved Ice • Vanilla Flavored Syrup Put scoops of ice cream in a bowl.
ENGLISH RETURNS & WARRANTY SHOULD YOUR UNIT NOT WORK OR IS DAMAGED WHEN YOU FIRST TAKE IT OUT OF THE BOX, PLEASE RETURN IT TO THE PLACE OF PURCHASE IMMEDIATELY. OLD FASHIONED SNOW CONE CART / SCC200 Should you have any questions, please contact us via email or at the customer service number listed below between the hours of 8:00 AM and 5:00 PM, Monday through Friday, Central Standard Time. Distributed by: Nostalgia Products Group LLC 1471 Partnership Dr.
