BST Doorphone Installation and Configuration Guide BCM Business Communications Manager Document Status:Standard Document Number: NN40010-302 Document Version: 01.
Copyright © 2005–2007 Nortel Networks, All Rights Reserved All rights reserved. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this document is proprietary to Nortel Networks.
Contents 3 Contents About the Business Series Terminal (BST) Doorphone . . . . . . . . . . . . . . . . 5 What you need to know . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Environment requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 How to get help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents NN40010-302
Chapter 1 About the Business Series Terminal (BST) Doorphone This guide leads a Nortel installer and/or system administrator through installing and configuring a BST Doorphone on a Business Communications Manager (BCM) system. The BST Doorphone is used as an intercom device to control access to your building. It provides call notification and handsfree communication from a site entry location to assigned telephones on the BCM system.
Chapter 1 About the Business Series Terminal (BST) Doorphone How to get help This section explains how to get help for Nortel products and services. Getting Help from the Nortel Web site The best way to get technical support for Nortel products is from the Nortel Technical Support Web site: http://www.nortel.com/support This site provides quick access to software, documentation, bulletins, and tools to address issues with Nortel products.
Chapter 2 DN configuration requirements for the BST Doorphone You can set up the DN record prior to a hardware installation, or you can install the hardware before you configure the DN record. If you install the hardware first, Element Manager will automatically detect the BST Doorphone and list it in the Active DNs table. Note: Some default DN settings can cause the BST Doorphone to automatically answer incoming calls that are not intended to be heard over the BST Doorphone.
Chapter 2 DN configuration requirements for the BST Doorphone Use Table 2 to set line access parameters for the BST Doorphone. Table 2 Line access parameters Tab Attribute Values Description Main panel Fwd No Answer up to 24 digits Leave blank for the BST Doorphone. Fwd Busy up to 24 digits Leave blank for the BST Doorphone. Line Assignment Line read only Ensure there is no line assignment for this DN.
Chapter 2 DN configuration requirements for the BST Doorphone 9 Other BST Doorphone configuration requirements You must configure the Trunk/line data and Scheduled Services for the BST Doorphone to work properly. Trunk/line data Ensure that the BST Doorphone DN (DN XXX) is not assigned as a prime set for lines on the BCM system. The Element Manager displays all active lines under: Configuration > Telephony > Lines > Active Physical Lines headings.
Chapter 2 DN configuration requirements for the BST Doorphone NN40010-302
Chapter 3 BST Doorphone Installation The BST Doorphone can be mounted in a standard recessed double-gang electrical box for flush mounting or surface mounted using the optional surface mount bracket. Mount the BST Doorphone at shoulder height (approximately 5 ft.) in the absence of other specifications, such as compliance with local handicapped access regulations, if required. Select a location for the BST Doorphone within 300 m (1000 ft.) of the BCM system.
Chapter 3 BST Doorphone Installation For a flush mount: (into an electrical box embedded in the wall) • Discard the surface mount gasket and bracket. • Slide the flush mount gasket onto the main housing assembly. Figure 2 Flush mount Wall Main housing assembly Flush mount gasket 3 Run a standard 3-pair cable from the BCM system to the BST Doorphone location. Use one pair to connect the ''KSU'' terminals of the BST Doorphone to a reserved station module port on the BCM system.
Chapter 3 BST Doorphone Installation 13 Initialize a new BST Doorphone The system automatically recognizes the BST Doorphone once it is installed and connected. Use the following commands, to refresh the Element Manager view in order for the BST Doorphone to appear in the Active Sets panel. • In Element Manager, click on the IP address in the Network Elements pane. Go to the top menu and select View > Refresh. Element Manager refreshes and the allows BST Doorphones to appear in the system.
Chapter 3 BST Doorphone Installation NN40010-302
Chapter 4 Configuring BST Doorphone settings 15 Chapter 4 Configuring BST Doorphone settings Doorphone programming allows you to customize feature settings for individual BST Doorphones on the BCM system. Follow these steps to configure Doorphone settings: 1 From Element Manager, click on the Configuration tab and select Telephony > Sets > Active Sets. Note: A maximum of 250 BST Doorphones can be attached to the BCM system.
Chapter 4 Configuring BST Doorphone settings Table 4 BST Doorphone settings (Sheet 2 of 2) Setting Values Description Page Target Internal External Both Internal: Make a page announcement to a specific group of telephones in a page zone, through the telephone speakers. External: Make a page announcement through an external loudspeaker system. Both: Make a page announcement through telephone speakers and an external loudspeaker system.
Chapter 4 Configuring BST Doorphone settings 17 — To open the door, dial the single digit code (specified in Doorphone programming) or on a two-line display telephone, press the OPEN display button. — Press the release button or hang up to end the test. Doorphone configuration tips • The Doorphone’s Target DN telephone should be assigned to the same page zone that is used by the Doorphone for paging (chime presentation). • The Doorphone can ring several telephones on the system using Answer DNs.
Chapter 4 Configuring BST Doorphone settings NN40010-302
