User's Manual
Table Of Contents
- Contents
- Preface
- The Command Line Interface
- First-Time Configuration
- Using the Setup Utility
- Setting Passwords
- Menu Basics
- The Information Menu
- Information Menu
- System Information
- Layer 2 Information
- Layer 3 Information
- IP Routing Information
- ARP Information
- BGP Information
- BGP Peer information
- BGP Summary information
- OSPF Information
- Routing Information Protocol Information
- IP Information
- IGMP Multicast Group Information
- IGMP Group Information
- IGMP Multicast Router Port Information
- IGMP Mrouter Information
- VRRP Information
- Quality of Service Information
- 802.1p Information
- Access Control List Information
- Link Status Information
- Port Information
- Logical Port to GEA Port Mapping
- Fiber Port SFP Status
- Information Dump
- The Statistics Menu
- The Configuration Menu
- Configuration Menu
- Viewing, Applying, and Saving Changes
- System Configuration
- Port Configuration
- Layer 2 Configuration
- 802.1x Configuration
- Rapid Spanning Tree Protocol/ Multiple Spanning Tree Protocol Configuration
- Common Internal Spanning Tree Configuration
- Spanning Tree Configuration
- GVRP Configuration
- GVRP Port Configuration
- Trunk Configuration
- IP Trunk Hash Configuration
- LACP Configuration
- Layer 2 Failover Configuration
- VLAN Configuration
- Protocol-based VLAN Configuration
- Private VLAN Configuration
- Layer 3 Configuration
- IP Interface Configuration
- Default Gateway Configuration
- IP Static Route Configuration
- IP Multicast Route Configuration
- ARP Configuration
- IP Forwarding Configuration
- Network Filter Configuration
- Routing Map Configuration
- Routing Information Protocol Configuration
- Open Shortest Path First Configuration
- Border Gateway Protocol Configuration
- IGMP Configuration
- Domain Name System Configuration
- Bootstrap Protocol Relay Configuration
- VRRP Configuration
- Quality of Service Configuration
- Access Control List Configuration
- Port Mirroring Configuration
- Setup
- Dump
- Saving the Active Switch Configuration
- Restoring the Active Switch Configuration
- The Operations Menu
- The Boot Options Menu
- The Maintenance Menu
- Alteon OS Syslog Messages
- Alteon OS SNMP Agent
- Glossary
- Index
Alteon OS Command Reference
360
Alteon OS Syslog Messages 43W7774, May 2007
LOG_ERROR (continued)
LOG_NOTICE
VRRP Multiple static routes have same destination
VRRP Virtual router <vr_id> must have sharing disabled when hotstandby is
enabled
VRRP Virtual router group must be enabled when hotstandby is enabled
VRRP At least one virtual router must be enabled when group is enabled
VRRP Virtual router group must have sharing disabled when hotstandby is
enabled
VRRP Virtual router group must have pre-emption enabled when hotstandby is
enabled
VRRP Virtual router <vr_id> must have an IP address
VRRP Virtual router <vr_id> cannot have same VRID and VLAN as <vlan_id>
VRRP Virtual router <vr_id> cannot have same IP address as <ip_address>
VRRP Virtual router <vr_id> corresponding virtual server <server_id> is not
enabled
CLI Duplicate default entry
CLI BGP peer <bgp_peer_id> must have an IP address
CLI BGP peers <bgp_peer_id> and <bgp_peer_id> have same address
CLI BGP peer <bgp_peer_id> have same address as IP interface
<ip_interface_id>
CLI BGP peer <bgp_peer_id> IP interface <ip_interface_id> is not enabled
SYSTEM Rebooted <last_reset_information>
SYSTEM Rebooted <last_reset_information> administrator logged in
SYSTEM Enable auto negotiation for copper GIG port: <port>
SYSTEM Change fiber GIG port <port> mode to full duplex
SYSTEM Change fiber GIG port <port> speed to 1000
MGMT Boot config block changed
MGMT Boot image changed
MGMT Switch reset from CLI
MGMT Syslog host changed to <ip_address>
MGMT Syslog host changed to this host