User's Manual
Table Of Contents
- Contents
- Preface
- The Command Line Interface
- First-Time Configuration
- Using the Setup Utility
- Setting Passwords
- Menu Basics
- The Information Menu
- Information Menu
- System Information
- Layer 2 Information
- Layer 3 Information
- IP Routing Information
- ARP Information
- BGP Information
- BGP Peer information
- BGP Summary information
- OSPF Information
- Routing Information Protocol Information
- IP Information
- IGMP Multicast Group Information
- IGMP Group Information
- IGMP Multicast Router Port Information
- IGMP Mrouter Information
- VRRP Information
- Quality of Service Information
- 802.1p Information
- Access Control List Information
- Link Status Information
- Port Information
- Logical Port to GEA Port Mapping
- Fiber Port SFP Status
- Information Dump
- The Statistics Menu
- The Configuration Menu
- Configuration Menu
- Viewing, Applying, and Saving Changes
- System Configuration
- Port Configuration
- Layer 2 Configuration
- 802.1x Configuration
- Rapid Spanning Tree Protocol/ Multiple Spanning Tree Protocol Configuration
- Common Internal Spanning Tree Configuration
- Spanning Tree Configuration
- GVRP Configuration
- GVRP Port Configuration
- Trunk Configuration
- IP Trunk Hash Configuration
- LACP Configuration
- Layer 2 Failover Configuration
- VLAN Configuration
- Protocol-based VLAN Configuration
- Private VLAN Configuration
- Layer 3 Configuration
- IP Interface Configuration
- Default Gateway Configuration
- IP Static Route Configuration
- IP Multicast Route Configuration
- ARP Configuration
- IP Forwarding Configuration
- Network Filter Configuration
- Routing Map Configuration
- Routing Information Protocol Configuration
- Open Shortest Path First Configuration
- Border Gateway Protocol Configuration
- IGMP Configuration
- Domain Name System Configuration
- Bootstrap Protocol Relay Configuration
- VRRP Configuration
- Quality of Service Configuration
- Access Control List Configuration
- Port Mirroring Configuration
- Setup
- Dump
- Saving the Active Switch Configuration
- Restoring the Active Switch Configuration
- The Operations Menu
- The Boot Options Menu
- The Maintenance Menu
- Alteon OS Syslog Messages
- Alteon OS SNMP Agent
- Glossary
- Index
Alteon OS Command Reference
284
The Configuration Menu 43W7774, May 2007
/cfg/l3/igmp/snoop/igmpv3
IGMP Version 3 Configuration
Table 6-83 describes the commands used to configure IGMP version 3.
ena
Enables IGMP Snooping.
dis
Disables IGMP Snooping.
cur
Displays the current IGMP Snooping parameters.
[IGMP V3 Snoop Menu]
sources - Set the number of sources to snoop in group record
v1v2 - Enable/disable snooping IGMPv1/v2 reports
exclude - Enable/disable snooping EXCLUDE mode reports
ena - Enable IGMPv3 Snooping
dis - Disable IGMPv3 Snooping
cur - Display current IGMP Snooping V3 configuration
Table 6-81 IGMP V3 Menu Options (/cfg/l3/igmp/snoop/igmpv3)
Command Syntax and Usage
sources <1-64>
Configures the maximum number of IGMP multicast sources to snoop from within the group
record. Use this command to limit the number of IGMP sources to provide more refined control.
v1v2 enable|disable
Enables or disables snooping on IGMP version 1 and version 2 reports. When disabled, the switch
drops IGMPv1 and IGMPv2 reports. The default value is enabled.
exclude enable|disable
Enables or disables snooping on IGMPv3 Exclude Reports. When disabled, the switch ignores
Exclude Reports. The default value is enabled.
ena
Enables IGMP version 3. The default value is disabled.
Table 6-80 IGMP Snoop Menu Options (/cfg/l3/igmp/snoop)
Command Syntax and Usage