User's Manual
Table Of Contents
- Contents
- Preface
- The Command Line Interface
- First-Time Configuration
- Using the Setup Utility
- Setting Passwords
- Menu Basics
- The Information Menu
- Information Menu
- System Information
- Layer 2 Information
- Layer 3 Information
- IP Routing Information
- ARP Information
- BGP Information
- BGP Peer information
- BGP Summary information
- OSPF Information
- Routing Information Protocol Information
- IP Information
- IGMP Multicast Group Information
- IGMP Group Information
- IGMP Multicast Router Port Information
- IGMP Mrouter Information
- VRRP Information
- Quality of Service Information
- 802.1p Information
- Access Control List Information
- Link Status Information
- Port Information
- Logical Port to GEA Port Mapping
- Fiber Port SFP Status
- Information Dump
- The Statistics Menu
- The Configuration Menu
- Configuration Menu
- Viewing, Applying, and Saving Changes
- System Configuration
- Port Configuration
- Layer 2 Configuration
- 802.1x Configuration
- Rapid Spanning Tree Protocol/ Multiple Spanning Tree Protocol Configuration
- Common Internal Spanning Tree Configuration
- Spanning Tree Configuration
- GVRP Configuration
- GVRP Port Configuration
- Trunk Configuration
- IP Trunk Hash Configuration
- LACP Configuration
- Layer 2 Failover Configuration
- VLAN Configuration
- Protocol-based VLAN Configuration
- Private VLAN Configuration
- Layer 3 Configuration
- IP Interface Configuration
- Default Gateway Configuration
- IP Static Route Configuration
- IP Multicast Route Configuration
- ARP Configuration
- IP Forwarding Configuration
- Network Filter Configuration
- Routing Map Configuration
- Routing Information Protocol Configuration
- Open Shortest Path First Configuration
- Border Gateway Protocol Configuration
- IGMP Configuration
- Domain Name System Configuration
- Bootstrap Protocol Relay Configuration
- VRRP Configuration
- Quality of Service Configuration
- Access Control List Configuration
- Port Mirroring Configuration
- Setup
- Dump
- Saving the Active Switch Configuration
- Restoring the Active Switch Configuration
- The Operations Menu
- The Boot Options Menu
- The Maintenance Menu
- Alteon OS Syslog Messages
- Alteon OS SNMP Agent
- Glossary
- Index
Alteon OS Command Reference
The Configuration Menu
20943W7774, May 2007
/cfg/port <port alias or number>
Port Configuration
Use the Port Configuration menu to configure settings for individual switch ports, except the
management port (MGT). This command is enabled by default.
[Port INT1 Menu]
gig - Gig Phy Menu
aclqos - Acl/Qos Configuration Menu
8021ppri - Set default 802.1p priority
pvid - Set default port VLAN id
name - Set port name
dscpmrk - Enable/disable DSCP remarking for port
learn - Enable/Disable FDB Learning for port
tag - Enable/disable VLAN tagging for port
tagpvid - Enable/disable tagging on pvid
fastfwd - Enable/disable Port Fast Forwarding mode
floodblk - Enable/disable Port flood blocking
ena - Enable port
dis - Disable port
cur - Display current port configuration
Table 6-25 Port Configuration Menu (/cfg/port)
Command Syntax and Usage
gig
If a port is configured to support Gigabit Ethernet, this option displays the Gigabit Ethernet Physi-
cal Link Menu. To view menu options, see page 211.
aclqos
Displays the ACL Quality of Service Menu. To view menu options, see page 212.
8021ppri <0-7>
Configures the port’s 802.1p priority level.
pvid <VLAN number, 1-4095>
Sets the default VLAN number which will be used to forward frames which are not VLAN tagged.
The default number is 1 for non-management ports.
name <64 character string>|none
Sets a name for the port. The assigned port name appears next to the port number on some infor-
mation and statistics screens. The default is set to None.
dscpmark
Enables or disables DSCP re-marking on a port.