User's Manual
Table Of Contents
- Contents
- Preface
- The Command Line Interface
- First-Time Configuration
- Using the Setup Utility
- Setting Passwords
- Menu Basics
- The Information Menu
- Information Menu
- System Information
- Layer 2 Information
- Layer 3 Information
- IP Routing Information
- ARP Information
- BGP Information
- BGP Peer information
- BGP Summary information
- OSPF Information
- Routing Information Protocol Information
- IP Information
- IGMP Multicast Group Information
- IGMP Group Information
- IGMP Multicast Router Port Information
- IGMP Mrouter Information
- VRRP Information
- Quality of Service Information
- 802.1p Information
- Access Control List Information
- Link Status Information
- Port Information
- Logical Port to GEA Port Mapping
- Fiber Port SFP Status
- Information Dump
- The Statistics Menu
- The Configuration Menu
- Configuration Menu
- Viewing, Applying, and Saving Changes
- System Configuration
- Port Configuration
- Layer 2 Configuration
- 802.1x Configuration
- Rapid Spanning Tree Protocol/ Multiple Spanning Tree Protocol Configuration
- Common Internal Spanning Tree Configuration
- Spanning Tree Configuration
- GVRP Configuration
- GVRP Port Configuration
- Trunk Configuration
- IP Trunk Hash Configuration
- LACP Configuration
- Layer 2 Failover Configuration
- VLAN Configuration
- Protocol-based VLAN Configuration
- Private VLAN Configuration
- Layer 3 Configuration
- IP Interface Configuration
- Default Gateway Configuration
- IP Static Route Configuration
- IP Multicast Route Configuration
- ARP Configuration
- IP Forwarding Configuration
- Network Filter Configuration
- Routing Map Configuration
- Routing Information Protocol Configuration
- Open Shortest Path First Configuration
- Border Gateway Protocol Configuration
- IGMP Configuration
- Domain Name System Configuration
- Bootstrap Protocol Relay Configuration
- VRRP Configuration
- Quality of Service Configuration
- Access Control List Configuration
- Port Mirroring Configuration
- Setup
- Dump
- Saving the Active Switch Configuration
- Restoring the Active Switch Configuration
- The Operations Menu
- The Boot Options Menu
- The Maintenance Menu
- Alteon OS Syslog Messages
- Alteon OS SNMP Agent
- Glossary
- Index
Alteon OS Command Reference
202
The Configuration Menu 43W7774, May 2007
cfg/sys/access
System Access Configuration
[System Access Menu]
mgmt - Management Network Definition Menu
user - User Access Control Menu (passwords)
http - Enable/disable HTTP (Web) access
https - HTTPS Web Access Menu
wport - Set HTTP (Web) server port number
snmp - Set SNMP access control
userbbi - Enable/disable user configuration from BBI
tnet - Enable/disable Telnet access
tnport - Set Telnet server port number
tport - Set the TFTP port for the system
cur - Display current system access configuration
Table 6-19 System Access Menu Options (/cfg/sys/access)
Command Syntax and Usage
mgmt
Displays the Management Configuration Menu. To view menu options, see page 204.
user
Displays the User Access Control Menu. To view menu options, see page 205.
http disable|enable
Enables or disables HTTP (Web) access to the Browser-Based Interface. It is enabled by default.
https
Displays the HTTPS Menu. To view menu options, see page 208.
wport <TCP port number (1-65535)>
Sets the switch port used for serving switch Web content. The default is HTTP port 80. If Global
Server Load Balancing is to be used, set this to a different port (such as 8080).
snmp disable|read-only|read-write
Disables or provides read-only/write-read SNMP access.
userbbi enable|disable
Enables or disables user configuration access through the Browser-Based Interface (BBI).
tnet enable|disable
Enables or disables Telnet access. This command is enabled by default. You will see this command
only if you are connected to the switch through a serial connection.
tnport <TCP port number>
Sets an optional telnet server port number for cases where the server listens for telnet sessions on a
non-standard port.