User's Manual
Table Of Contents
- Contents
- Preface
- The Command Line Interface
- First-Time Configuration
- Using the Setup Utility
- Setting Passwords
- Menu Basics
- The Information Menu
- Information Menu
- System Information
- Layer 2 Information
- Layer 3 Information
- IP Routing Information
- ARP Information
- BGP Information
- BGP Peer information
- BGP Summary information
- OSPF Information
- Routing Information Protocol Information
- IP Information
- IGMP Multicast Group Information
- IGMP Group Information
- IGMP Multicast Router Port Information
- IGMP Mrouter Information
- VRRP Information
- Quality of Service Information
- 802.1p Information
- Access Control List Information
- Link Status Information
- Port Information
- Logical Port to GEA Port Mapping
- Fiber Port SFP Status
- Information Dump
- The Statistics Menu
- The Configuration Menu
- Configuration Menu
- Viewing, Applying, and Saving Changes
- System Configuration
- Port Configuration
- Layer 2 Configuration
- 802.1x Configuration
- Rapid Spanning Tree Protocol/ Multiple Spanning Tree Protocol Configuration
- Common Internal Spanning Tree Configuration
- Spanning Tree Configuration
- GVRP Configuration
- GVRP Port Configuration
- Trunk Configuration
- IP Trunk Hash Configuration
- LACP Configuration
- Layer 2 Failover Configuration
- VLAN Configuration
- Protocol-based VLAN Configuration
- Private VLAN Configuration
- Layer 3 Configuration
- IP Interface Configuration
- Default Gateway Configuration
- IP Static Route Configuration
- IP Multicast Route Configuration
- ARP Configuration
- IP Forwarding Configuration
- Network Filter Configuration
- Routing Map Configuration
- Routing Information Protocol Configuration
- Open Shortest Path First Configuration
- Border Gateway Protocol Configuration
- IGMP Configuration
- Domain Name System Configuration
- Bootstrap Protocol Relay Configuration
- VRRP Configuration
- Quality of Service Configuration
- Access Control List Configuration
- Port Mirroring Configuration
- Setup
- Dump
- Saving the Active Switch Configuration
- Restoring the Active Switch Configuration
- The Operations Menu
- The Boot Options Menu
- The Maintenance Menu
- Alteon OS Syslog Messages
- Alteon OS SNMP Agent
- Glossary
- Index
Alteon OS Command Reference
The Configuration Menu
18343W7774, May 2007
Table 6-6 TACACS+ Server Menu Options (/cfg/sys/tacacs)
Command Syntax and Usage
prisrv <IP address>
Defines the primary TACACS+ server address.
secsrv <IP address>
Defines the secondary TACACS+ server address.
secret <1-32 character secret>
This is the shared secret between the switch and the TACACS+ server(s).
secret2 <1-32 character secret>
This is the secondary shared secret between the switch and the TACACS+ server(s).
port <TACACS port configure, default 49>
Enter the number of the TCP port to be configured, between 1 - 65000. The default is 49.
retries <TACACS server retries, 1-3>
Sets the number of failed authentication requests before switching to a different TACACS+ server.
The default is 3 requests.
timeout <TACACS server timeout seconds, 4-15>
Sets the amount of time, in seconds, before a TACACS+ server authentication attempt is consid-
ered to have failed. The default is 5 seconds.
telnet disable|enable
Enables or disables the TACACS+ back door for telnet. The telnet command also applies to
SSH/SCP connections, and the Browser-Based Interface (BBI). The default is disabled.
To obtain the TACACS+ backdoor password for your GbESM, contact your IBM Service and
Support line.
secbd enable|disable
Enables or disables TACACS+ secure backdoor access through telnet, SSH, or HTTP.
cmap enable|disable
Enables or disables TACACS+ privilege-level mapping.
The default value is disabled.
passch enable|disable
Enables or disables TACACS+ password change.
The default value is disabled.
chpass_p
Configures the password for the primary TACACS+ server. The CLI will prompt you for input.
chpass_s
Configures the password for the secondary TACACS+ server. The CLI will prompt you for input.