User's Manual
Table Of Contents
- Contents
- Preface
- The Command Line Interface
- First-Time Configuration
- Using the Setup Utility
- Setting Passwords
- Menu Basics
- The Information Menu
- Information Menu
- System Information
- Layer 2 Information
- Layer 3 Information
- IP Routing Information
- ARP Information
- BGP Information
- BGP Peer information
- BGP Summary information
- OSPF Information
- Routing Information Protocol Information
- IP Information
- IGMP Multicast Group Information
- IGMP Group Information
- IGMP Multicast Router Port Information
- IGMP Mrouter Information
- VRRP Information
- Quality of Service Information
- 802.1p Information
- Access Control List Information
- Link Status Information
- Port Information
- Logical Port to GEA Port Mapping
- Fiber Port SFP Status
- Information Dump
- The Statistics Menu
- The Configuration Menu
- Configuration Menu
- Viewing, Applying, and Saving Changes
- System Configuration
- Port Configuration
- Layer 2 Configuration
- 802.1x Configuration
- Rapid Spanning Tree Protocol/ Multiple Spanning Tree Protocol Configuration
- Common Internal Spanning Tree Configuration
- Spanning Tree Configuration
- GVRP Configuration
- GVRP Port Configuration
- Trunk Configuration
- IP Trunk Hash Configuration
- LACP Configuration
- Layer 2 Failover Configuration
- VLAN Configuration
- Protocol-based VLAN Configuration
- Private VLAN Configuration
- Layer 3 Configuration
- IP Interface Configuration
- Default Gateway Configuration
- IP Static Route Configuration
- IP Multicast Route Configuration
- ARP Configuration
- IP Forwarding Configuration
- Network Filter Configuration
- Routing Map Configuration
- Routing Information Protocol Configuration
- Open Shortest Path First Configuration
- Border Gateway Protocol Configuration
- IGMP Configuration
- Domain Name System Configuration
- Bootstrap Protocol Relay Configuration
- VRRP Configuration
- Quality of Service Configuration
- Access Control List Configuration
- Port Mirroring Configuration
- Setup
- Dump
- Saving the Active Switch Configuration
- Restoring the Active Switch Configuration
- The Operations Menu
- The Boot Options Menu
- The Maintenance Menu
- Alteon OS Syslog Messages
- Alteon OS SNMP Agent
- Glossary
- Index
Alteon OS Command Reference
176
The Configuration Menu 43W7774, May 2007
ssnmp
Displays the System SNMP Menu. To view menu options, see page 189.
access
Displays the System Access Menu. To view menu options, see page 202.
date
Prompts the user for the system date. The date reverts to its default value when the switch is reset.
time
Configures the system time using a 24-hour clock format. The time reverts to its default value
when the switch is reset.
timezone
Configures the time zone where the switch resides. You are prompted to select your location (con-
tinent, country, region) by the timezone wizard. Once a region is selected, the switch updates the
time to reflect local changes to Daylight Savings Time, etc.
olddst enable|disable
Enables or disables use of the Daylight Saving Time (DST) rules in effect prior to the year 2007.
The default value is disabled.
idle <idle timeout in minutes>
Sets the idle timeout for CLI sessions, from 1 to 60 minutes. The default is 5 minutes.
notice <max 1024 char multi-line login notice> <'-' to end>
Displays login notice immediately before the “Enter password:” prompt. This notice can contain
up to 1024 characters and new lines.
bannr <string, maximum 80 characters>
Configures a login banner of up to 80 characters. When a user or administrator logs into the switch,
the login banner is displayed. It is also displayed as part of the output from the /info/sys com-
mand.
hprompt disable|enable
Enables or disables displaying of the host name (system administrator’s name) in the Command
Line Interface (CLI).
reminder disable|enable
Enables or disables reminder messages in the CLI. The default value is enabled.
cur
Displays the current system parameters.
Table 6-2 System Configuration Menu Options (/cfg/sys)
Command Syntax and Usage