User manual
Table Of Contents
- Title page
- New in this release
- List of Procedures
- How to get help
- Finding the latest updates on the Nortel web site
- System information
- Introduction
- Preparing for installation
- Placing the fourth module on a column
- Positioning and leveling equipment
- Installing AC power
- Installing overhead cable tray kits
- Installing DC power
- Contents
- DC-powered systems
- Candeo DC power systems
- Large Candeo modules
- Small Candeo modules
- Installation reference guide
- Configuration reference guide
- Safety ground/protective earth and logic return wiring
- Cabling and connecting the grounding leads
- Connecting the power plant frame ground (or safety ground) leads
- Four-Feed PDU
- Installing the Four-Feed PDU
- Installing safety ground/protective earth wiring
- Connecting power from the power plant to the PDU
- Connecting UK power to the Four-Feed PDU
- System monitor connections
- Planning and designating a Main Distribution Frame
- Installing Power Failure Transfer Units
- Configuring the system monitor
- Connecting a system terminal or modem
- Contents
- About the system terminal
- Connecting a terminal
- Connecting a terminal to a COM port
- Connecting a switch box and terminal to COM1 and COM2 ports
- Connecting a switch box and terminal to SDI and COM1 ports
- Connecting a modem
- Configuring a modem
- Connecting a modem to an SDI port
- Connecting a modem to switch box, COM2 ports, SDI ports
- Cabling Common Equipment in a Single Group system
- Contents
- Cabling guidelines
- Core/Net module
- Cabling the Core side
- Cabling the I/O panel
- Cabling the Network side
- Configuring and cabling the Clock Controllers
- Network Group 0: Shelf 0 to Shelf 1
- Connecting the 3PE faceplates in the Core/Net modules
- Inspecting CNI to 3PE factory installed cables
- Connecting the Core/Net backplanes
- Optioning the System Utility Card
- Connecting Core modules to a LAN
- Cabling Common Equipment in a Multi Group system
- Contents
- Cabling guidelines
- Core/Net module
- Cabling the Core/Net module backplane
- Disconnecting cables from the Core/Net module backplane
- Optioning the System Utility Card
- Core shelf cabling
- Installing the CP PIV to I/O panel cables
- Connecting the Core module to a LAN
- Cabling a Dual Ring Fiber Network
- FIJI card cabling
- Installing the Shelf 0 fiber optic ring (ascending)
- Installing the Shelf 1 fiber optic ring (descending)
- FIJI to FIJI cabling
- Connecting the Clock Controller cables
- Cabling network modules and loops
- Contents
- Network-to-network cabling
- Network module connections
- Network Group 0: Shelf 0 to Shelf 1
- Connecting the 3PE faceplates in the Core/Net modules
- Connecting the Core/Net backplanes
- Connecting Groups 1 through 7: Shelf 0 to Shelf 1
- Connecting the Network modules to the Core/Net modules
- Connecting the 3PE cables to the 3PE fanout panels
- Cabling a Superloop Network Card - single column
- Cabling a Superloop Network Card - multiple columns
- Cabling lines and trunks
- Powering up the system and initial loading
- Performing acceptance tests
- Installing earthquake bracing
- Adding a module to a column
- Installing a Signaling Server
- Contents
- Introduction
- Readiness checklist
- Installing the CP PM Signaling Server hardware
- Connections
- Installing the Signaling Server software
- First boot of a new Nortel CP PM Signaling Server
- Unpacking Help files for Virtual Terminal Emulator
- Logging in to the Signaling Server
- Verifying a successful configuration
- Testing the Leader Signaling Server
- Index
Page 456 of 458 Index
NN43021-310 Standard 02.02 October 2008
positioning
earthquake bracing, 359
equipment, 71
positioning guides
fourth modules, 66
module additions, 374, 380
power cables
fourth modules, 68
module additions, 370, 371, 373, 381, 382
power cords, 82
power systems, 59, 93
power-up
preparations, 301
PWR messages in acceptance tests
module power supply, 338
R
ramps, 58
receptacles, 77
ringing generators
acceptance tests, 338
rod installation
earthquake bracing, 353, 357
RS-232 cable
modem cabling, 181, 183
S
safety ground/protective earth
AC power, 78, 82
DC power, 109, 123
SDI (serial data interface) ports
modem connections, 179, 181, 183, 185, 186
system monitor interface, 153, 158
system terminal connections, 171
seismic anchor kits, 347, 348
seismic bracing kits, 347
Signaling Server, 45
single-column systems
bracing rod installation, 357
ground and logic return distribution, 79, 83,
123
system monitor option switches, 153
single-row systems
superloop cabling, 254, 257
slave switch settings
system monitor, 154
spacers and spacer kits, 40
bracing rod installation, 358, 359
multiple-column systems, 72
SPG (single-point ground), 78
split mode monitoring, 172, 173
static discharge, 59
superloop adapter plates, 258
superloop cabling, 254
switch boxes
modem connections, 183, 185, 186
system terminal connections, 175, 177
sysloads
acceptance tests, 341
System 600/48 Power Plant
PDU connections, 125
system installation procedures, 33
system monitors
acceptance tests, 342
cabling, 157
configuring, 151
for DC power, 121
fourth modules, 68
module additions, 367, 370, 371, 372, 373,
376, 381, 382
system monitors, cabling, 151, 157
system terminals, 171
acceptance tests, 342
connections, 172
CPIO port connections, 174, 175, 177