User manual
Table Of Contents
- Title page
- New in this release
- List of Procedures
- How to get help
- Finding the latest updates on the Nortel web site
- System information
- Introduction
- Preparing for installation
- Placing the fourth module on a column
- Positioning and leveling equipment
- Installing AC power
- Installing overhead cable tray kits
- Installing DC power
- Contents
- DC-powered systems
- Candeo DC power systems
- Large Candeo modules
- Small Candeo modules
- Installation reference guide
- Configuration reference guide
- Safety ground/protective earth and logic return wiring
- Cabling and connecting the grounding leads
- Connecting the power plant frame ground (or safety ground) leads
- Four-Feed PDU
- Installing the Four-Feed PDU
- Installing safety ground/protective earth wiring
- Connecting power from the power plant to the PDU
- Connecting UK power to the Four-Feed PDU
- System monitor connections
- Planning and designating a Main Distribution Frame
- Installing Power Failure Transfer Units
- Configuring the system monitor
- Connecting a system terminal or modem
- Contents
- About the system terminal
- Connecting a terminal
- Connecting a terminal to a COM port
- Connecting a switch box and terminal to COM1 and COM2 ports
- Connecting a switch box and terminal to SDI and COM1 ports
- Connecting a modem
- Configuring a modem
- Connecting a modem to an SDI port
- Connecting a modem to switch box, COM2 ports, SDI ports
- Cabling Common Equipment in a Single Group system
- Contents
- Cabling guidelines
- Core/Net module
- Cabling the Core side
- Cabling the I/O panel
- Cabling the Network side
- Configuring and cabling the Clock Controllers
- Network Group 0: Shelf 0 to Shelf 1
- Connecting the 3PE faceplates in the Core/Net modules
- Inspecting CNI to 3PE factory installed cables
- Connecting the Core/Net backplanes
- Optioning the System Utility Card
- Connecting Core modules to a LAN
- Cabling Common Equipment in a Multi Group system
- Contents
- Cabling guidelines
- Core/Net module
- Cabling the Core/Net module backplane
- Disconnecting cables from the Core/Net module backplane
- Optioning the System Utility Card
- Core shelf cabling
- Installing the CP PIV to I/O panel cables
- Connecting the Core module to a LAN
- Cabling a Dual Ring Fiber Network
- FIJI card cabling
- Installing the Shelf 0 fiber optic ring (ascending)
- Installing the Shelf 1 fiber optic ring (descending)
- FIJI to FIJI cabling
- Connecting the Clock Controller cables
- Cabling network modules and loops
- Contents
- Network-to-network cabling
- Network module connections
- Network Group 0: Shelf 0 to Shelf 1
- Connecting the 3PE faceplates in the Core/Net modules
- Connecting the Core/Net backplanes
- Connecting Groups 1 through 7: Shelf 0 to Shelf 1
- Connecting the Network modules to the Core/Net modules
- Connecting the 3PE cables to the 3PE fanout panels
- Cabling a Superloop Network Card - single column
- Cabling a Superloop Network Card - multiple columns
- Cabling lines and trunks
- Powering up the system and initial loading
- Performing acceptance tests
- Installing earthquake bracing
- Adding a module to a column
- Installing a Signaling Server
- Contents
- Introduction
- Readiness checklist
- Installing the CP PM Signaling Server hardware
- Connections
- Installing the Signaling Server software
- First boot of a new Nortel CP PM Signaling Server
- Unpacking Help files for Virtual Terminal Emulator
- Logging in to the Signaling Server
- Verifying a successful configuration
- Testing the Leader Signaling Server
- Index
Index Page 453 of 458
Communication Server 1000M and Meridian 1 Large System Installation and Commissioning
F
field wiring kits and terminals
PDU connections, 121
floor drilling for anchor bolts, 349
floor plans, 62
fourth modules, 65
G
gaskets
bracing rod installation, 358
spacer kits, 72
GFCI (ground fault circuit interrupt) devices, 77
global PDU, 94
grills, 63
ground/protective earth
AC power, 78, 82
DC power, 109, 123
UPS, 85
ground start feature, 149
I
IG (isolated ground) bus, 78
IG-L6-30 receptacles, 77
installing
QUA6 PFTU (UK), 150
insulated ground wire, 124
I/O panels
backplane connections, 264, 265
IPE module connections, 267
superloop cabling, 259, 261, 262
system terminal connections, 171
IPE modules
backplane slots, 138
cable connections, 263, 267
line pair-termination tables, 269
placement, 54
superloop cabling, 254, 258
trunk pair-termination tables, 269, 271
K
Krone cross connect system (UK), 138
L
L6-20 receptacles, 77
L6-30 receptacles, 77
labels
Krone cross connect system, 140
ladder racks, 89
LD 37 program
module additions, 367, 370, 372, 375, 376, 384
system terminal tests, 342
LED (light-emitting diodes)
blower unit acceptance tests, 339
power supply acceptance tests, 338
sysload acceptance tests, 341
leveling
earthquake bracing, 359
equipment, 71
lines
cabling, 263
connecting, 268
pair-termination tables, 268
terminal numbers, 268
line transfer switches, 343
locking latches, 63
logic return wiring
AC power, 78, 82
DC power, 109
LRE (logic return equalizers), 79, 84
M
master switch settings, system monitor, 154
MDF (modular distribution frames), 133
backplane cable expansion, 138
I/O panel connections, 265
PFTU cross-connections, 148
PFTU terminations, 146
system monitor cabling, 161