User manual
Table Of Contents
- Title page
- New in this release
- List of Procedures
- How to get help
- Finding the latest updates on the Nortel web site
- System information
- Introduction
- Preparing for installation
- Placing the fourth module on a column
- Positioning and leveling equipment
- Installing AC power
- Installing overhead cable tray kits
- Installing DC power
- Contents
- DC-powered systems
- Candeo DC power systems
- Large Candeo modules
- Small Candeo modules
- Installation reference guide
- Configuration reference guide
- Safety ground/protective earth and logic return wiring
- Cabling and connecting the grounding leads
- Connecting the power plant frame ground (or safety ground) leads
- Four-Feed PDU
- Installing the Four-Feed PDU
- Installing safety ground/protective earth wiring
- Connecting power from the power plant to the PDU
- Connecting UK power to the Four-Feed PDU
- System monitor connections
- Planning and designating a Main Distribution Frame
- Installing Power Failure Transfer Units
- Configuring the system monitor
- Connecting a system terminal or modem
- Contents
- About the system terminal
- Connecting a terminal
- Connecting a terminal to a COM port
- Connecting a switch box and terminal to COM1 and COM2 ports
- Connecting a switch box and terminal to SDI and COM1 ports
- Connecting a modem
- Configuring a modem
- Connecting a modem to an SDI port
- Connecting a modem to switch box, COM2 ports, SDI ports
- Cabling Common Equipment in a Single Group system
- Contents
- Cabling guidelines
- Core/Net module
- Cabling the Core side
- Cabling the I/O panel
- Cabling the Network side
- Configuring and cabling the Clock Controllers
- Network Group 0: Shelf 0 to Shelf 1
- Connecting the 3PE faceplates in the Core/Net modules
- Inspecting CNI to 3PE factory installed cables
- Connecting the Core/Net backplanes
- Optioning the System Utility Card
- Connecting Core modules to a LAN
- Cabling Common Equipment in a Multi Group system
- Contents
- Cabling guidelines
- Core/Net module
- Cabling the Core/Net module backplane
- Disconnecting cables from the Core/Net module backplane
- Optioning the System Utility Card
- Core shelf cabling
- Installing the CP PIV to I/O panel cables
- Connecting the Core module to a LAN
- Cabling a Dual Ring Fiber Network
- FIJI card cabling
- Installing the Shelf 0 fiber optic ring (ascending)
- Installing the Shelf 1 fiber optic ring (descending)
- FIJI to FIJI cabling
- Connecting the Clock Controller cables
- Cabling network modules and loops
- Contents
- Network-to-network cabling
- Network module connections
- Network Group 0: Shelf 0 to Shelf 1
- Connecting the 3PE faceplates in the Core/Net modules
- Connecting the Core/Net backplanes
- Connecting Groups 1 through 7: Shelf 0 to Shelf 1
- Connecting the Network modules to the Core/Net modules
- Connecting the 3PE cables to the 3PE fanout panels
- Cabling a Superloop Network Card - single column
- Cabling a Superloop Network Card - multiple columns
- Cabling lines and trunks
- Powering up the system and initial loading
- Performing acceptance tests
- Installing earthquake bracing
- Adding a module to a column
- Installing a Signaling Server
- Contents
- Introduction
- Readiness checklist
- Installing the CP PM Signaling Server hardware
- Connections
- Installing the Signaling Server software
- First boot of a new Nortel CP PM Signaling Server
- Unpacking Help files for Virtual Terminal Emulator
- Logging in to the Signaling Server
- Verifying a successful configuration
- Testing the Leader Signaling Server
- Index
Page 452 of 458 Index
NN43021-310 Standard 02.02 October 2008
C
cables and cabling
fourth modules, 68
lines and trunks, 263
module additions, 370, 371, 373, 381, 382
network loops, 241
PFTU, 148
routing guidelines, 54
superloops, 254
system monitors, 157
cable tray kits, 89
cabling
system monitor, 157
CALIFORNIA OSHPD specification, 346
call back modems, 179
Candeo DC power systems, 93
captive screws, 63
card allocations
Krone cross connect system, 138
casters, 71
CC (clock controller) cards
superloop cabling, 254, 258, 259
CE/PE (Common Equipment/Peripheral Equipment
line pair-termination tables, 269
CE/PE (Common Equipment/Peripheral
Equipment)
backplane slots, 138
trunk pair-termination tables, 269
circuit breakers
DC power, 118, 121
module additions, 367, 370, 372, 376, 384
circuit cards, 59
column height recommendations for modules, 53
columns, 38
adding modules to, 365
fourth modules on, 65
module additions, 376
configuring
system monitors, 151
connectors, 263
covers, module, 62
CP (call processing) cards
sysloads, 341
system terminal connections, 172
CPIO ports
modem connections, 179, 182, 183, 185, 186
system terminal connections, 174, 175, 177
CP PIV, 48
CPU modules
placement as bottom modules, 53
cross-connecting wire, 268
CS 1000M MG, 45
CS 1000M SG, 45
D
DC (direct current) power systems, 93
safety ground/protective earth and logic return
wiring, 109, 123
DCE (data communication equipment), 173
DC power, 152
dispatch modems, 179
DTE (data terminal equipment), 173
E
E&M trunk cards
pair-terminations, 272
earthquake bracing, 345
anchor plate installation, 351
floor drilling, 349
kit selection, 347
positioning and leveling, 359
rod installation, 353, 357
EMI shielding, 57
module additions, 369
superloop cards, 254, 258
equipment room floor plans, 62
external alarm cabling, 161