Nortel Secure Router 4134 Quick Start Release: 10.1 Document Revision: 02.01 www.nortel.com NN47263-100 .
Nortel Secure Router 4134 Release: 10.1 Publication: NN47263-100 Document status: Standard Document release date: 18 February 2008 Copyright © 2007, 2008 Nortel Networks All Rights Reserved. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty.
. Contents Secure Router 4134 regulatory information and safety precautions 7 International Regulatory Statements of Conformity 7 National Electromagnetic Compliance (EMC) Statements of Compliance 7 FCC statement (USA only) 7 TIA-968-A 8 ICES statement (Canada only) 8 CE marking statement (Europe only) 8 European Union and European Free Trade Association (EFTA) notice 9 VCCI statement (Japan/Nippon only) 10 BSMI statement (Taiwan only) 10 MIC notice (Republic of Korea only) 10 National Safety Statemen
Introduction Navigation 23 23 Secure Router 4134 installation and initial configuration 25 Secure Router 4134 installation and initial configuration tasks 25 Secure Router 4134 installation and initial configuration navigation 27 Installing the Secure Router 4134 chassis and hardware components 29 Unpacking and inspecting the Secure Router 4134 chassis 29 Installing a power supply module 30 Prerequisites 31 Installing the mounting brackets on the chassis 31 Prerequisites 33 Installing the chassis
Power cord warning statement 67 Nortel Secure Router 4134 Quick Start NN47263-100 02.01 Standard 18 February 2008 Copyright © 2007, 2008 Nortel Networks .
Nortel Secure Router 4134 Quick Start NN47263-100 02.01 Standard 18 February 2008 Copyright © 2007, 2008 Nortel Networks .
. Secure Router 4134 regulatory information and safety precautions International Regulatory Statements of Conformity This is to certify that the Nortel Secure Router 4134 equipment was evaluated to the international regulatory standards for electromagnetic compliance (EMC) and safety and were found to have met the requirements for the following international standards: • • • EMC – Electromagnetic Emissions – CISPR 22, Class A EMC – Electromagnetic Immunity – CISPR 24 Electrical Safety – IEC 60950, wit
Secure Router 4134 regulatory information and safety precautions TIA-968-A This equipment complies with Part 68 of the FCC rules. The FCC Part 68 label is located on the bottom chassis panel. This label contains the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. If requested, this information must be provided to your telephone company. Connection to the telephone network should be made by using standard modular telephone jacks, type RJ-48C.
National Electromagnetic Compliance (EMC) Statements of Compliance 9 CAUTION This device is a Class A product. In a domestic environment, this device can cause radio interference, in which case the user may be required to take appropriate measures. For translations of this message, see “Translations of safety messages” (page 63). CAUTION ACHTUNG Dies ist ein Gerät der Klasse A. Bei Einsatz des Geräts in Wohngebieten kann es Störungen des Radio- und Fernsehempfangs verursachen.
Secure Router 4134 regulatory information and safety precautions • • EN 61000-3-2 (IEC 610000-3-2)–Power Line Harmonics EN 61000-3-3 (IEC 610000-3-3)–Power Line Flicker VCCI statement (Japan/Nippon only) This is a Class A product based on the standard of the Voluntary Control Council for Interference (VCCI) for information technology equipment. If this equipment is used in a domestic environment, radio disturbance may arise.
National Safety Statements of Compliance 11 National Safety Statements of Compliance EN 60950 statement This is to certify that the Nortel Secure Router 4134 equipment is in compliance with the requirements of EN 60950 in accordance with the Low Voltage Directive. Additional national differences for all European Union countries have been evaluated for compliance.
Secure Router 4134 regulatory information and safety precautions Exportador: Nortel Networks, 5400 Hellyer Ave, San Jose, CA 95138 USA. Importador: Nortel Networks de México, S.A. de C.V. Avenida Insurgentes Sur #1605 Piso 30, Oficina Col. San Jose Insurgentes Deleg-Benito Juarez México D.F.
Safety messages 13 Nortel declares compliance with the European Union (EU) RoHS Directive (2002/95/EC). WEEE Directive Compliance Statement This product at end of life is subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore is marked with the symbol shown at the left.
Secure Router 4134 regulatory information and safety precautions CAUTION Caution notices provide information about how to avoid possible service disruption or damage to Nortel products. CAUTION ACHTUNG Achtungshinweise bieten Informationen dazu, wie man mögliche Dienstunterbrechungen oder Schäden an Nortel-Produkten verhindert. WARNING Warning notices provide information about how to avoid personal injury when working with Nortel products.
Safety messages 15 Cautions and warnings for the Secure Router 4134 The following precautionary messages apply to the Secure Router 4134. For your safety, read these precautions carefully before proceeding with installation of the product. WARNING Only qualified service personnel must perform installation. Read and follow all warning notices and instructions marked on the product or included in the documentation. For translations of this statement, see “Translations of safety messages” (page 63).
Secure Router 4134 regulatory information and safety precautions CAUTION Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. CAUTION ACHTUNG Explosionsgefahr bei Ersetzen der Batterie durch falschen Typ. Entsorgung von gebrauchten Batterien gemäß Anleitung. Hardware Notice The Lithium battery in this product is part of a non-volatile memory device and will retain data for 10 years in the absence of power.
Safety messages 17 WARNING WARNUNG Risiko einer Augenverletzung durch Laser Glasfasergeräte können Laserstrahlen oder ultraviolettes Licht aussenden, das Ihre Augen verletzen kann. Schauen Sie nie direkt in einen Glasfaserleiter oder Verbindungsanschluss. Gehen Sie immer davon aus, dass Glasfaserkabel mit einer Lichtquelle verbunden sind. CAUTION If you do not install interface modules in slots, be sure to keep the metal cover plates in place over the slots.
Secure Router 4134 regulatory information and safety precautions WARNING The 2- and 4-port FXS interface modules have a ring signal generator that is a source of hazardous voltage. Do not touch the RJ11 port conductors, the conductors of a cable (that is, the exposed metal ends of a cable connector) connected to the RJ11 port, or the circuit board when the ringer is active (an incoming call activates the ringer).
Personal safety and equipment protection 19 • Ensure that your environment meets the requirements for temperature, humidity, and cleanliness. See “Environmental requirements” (page 61). • Do not overtighten thumb screws or lug nuts. Tighten screws and nuts until they are snug, plus a quarter turn. If you use a power tool to tighten screws, use a low torque setting of 2 to 3 in–lb (0.226 to 0.339 N-m).
Secure Router 4134 regulatory information and safety precautions Use a grounded ESD wrist strap. When you use a wrist strap, any charge in your body can go to ground rather than damage a hardware module. If you must ship the product, ensure you use proper antistatic packaging to shield the product from charge caused by movement of the product within the shipping container.
. New in this release The following section details what’s new in the Nortel Secure Router 4134 — Quick Start (NN47263-100) for Release 10.1. Features See the following sections for information about feature changes: • “Interface modules” (page 21) Interface modules Secure Router 4134, Release 10.
New in this release Nortel Secure Router 4134 Quick Start NN47263-100 02.01 Standard 18 February 2008 Copyright © 2007, 2008 Nortel Networks .
. Introduction Nortel Secure Router 4134 — Quick Start (NN47263-100) provides basic instruction on how to install the hardware and perform initial configuration of the Nortel Secure Router 4134. The Quick Start is intended for experienced installers.
Introduction Nortel Secure Router 4134 Quick Start NN47263-100 02.01 Standard 18 February 2008 Copyright © 2007, 2008 Nortel Networks .
. Secure Router 4134 installation and initial configuration Install the Secure Router 4134 and log on to prepare the unit for configuration and deployment in your network. Secure Router 4134 installation and initial configuration tasks This work flow shows you the sequence of tasks you perform to install the Secure Router 4134 and prepare the unit for system configuration. To link to any task, go to “Secure Router 4134 installation and initial configuration navigation” (page 27).
Secure Router 4134 installation and initial configuration Figure 1 Secure Router 4134 installation and initial configuration tasks Nortel Secure Router 4134 Quick Start NN47263-100 02.01 Standard 18 February 2008 Copyright © 2007, 2008 Nortel Networks .
Secure Router 4134 installation and initial configuration navigation 27 Secure Router 4134 installation and initial configuration navigation • “Unpacking and inspecting the Secure Router 4134 chassis” (page 29) • “Installing a power supply module” (page 30) • “Installing the mounting brackets on the chassis” (page 31) • “Installing the chassis” (page 34) • “Grounding the chassis” (page 36) • “Installing the interface modules” (page 39) • “Connecting power cables” (page 46) • “Powering up the router” (page
Secure Router 4134 installation and initial configuration Nortel Secure Router 4134 Quick Start NN47263-100 02.01 Standard 18 February 2008 Copyright © 2007, 2008 Nortel Networks .
. Installing the Secure Router 4134 chassis and hardware components For detailed instructions about how to install the Secure Router 4134 and its hardware components, see Nortel Secure Router 4134 Installation — Chassis (NN47263-300) and Nortel Secure Router 4134 Installation — Hardware Components (NN47263-301). The Secure Router 4134 ships with the fan tray installed, as well as the power supply unit or units that you ordered.
Installing the Secure Router 4134 chassis and hardware components Table 1 Secure Router 4134 accessories Accessory Function Rack mounting bracket kit that contains two rack mounting brackets and 20 Phillips-head screws. Supports the chassis in an equipment rack. The screws for the mounting brackets are 8-32 x 1/4 in. (12). There are two types of screws for the rack mount: For telecom racks—12-24 x 5/8 in. Phillips (4) For cabinets—10-32 x 1/2 in.
Installing the mounting brackets on the chassis 31 CAUTION ESD To prevent damage from electrostatic discharge, always wear an antistatic wrist strap connected to an electrostatic discharge (ESD) jack when performing maintenance on this product. Ensure that the wrist strap makes contact with your skin.
Installing the Secure Router 4134 chassis and hardware components Average time to install mounting brackets: 2 minutes. Table 2 Mounting bracket installation options Position Description Position 1 with front panel facing operator Position 2 with front panel facing operator Position 3 with front panel facing operator Nortel Secure Router 4134 Quick Start NN47263-100 02.01 Standard 18 February 2008 Copyright © 2007, 2008 Nortel Networks .
Installing the mounting brackets on the chassis 33 Table 2 Mounting bracket installation options (cont’d.) Position Description Position 1 with rear panel facing operator Position 2 with rear panel facing operator Position 3 with rear panel facing operator Prerequisites • Ensure you have the rack mounting brackets and screws that shipped with the Secure Router 4134. • Ensure you have a Phillips #2 screwdriver. Nortel Secure Router 4134 Quick Start NN47263-100 02.
Installing the Secure Router 4134 chassis and hardware components Procedure steps Step Action 1 Select one of the six possible rack-mounting positions on the sides of the Secure Router 4134. 2 Use a #2 Phillips screwdriver to attach a bracket to the desired mounting position on one side of the Secure Router 4134. 3 Torque the mounting bracket screws to 3 to 6 in-lb (0.339 to 0.6779 N-m). 4 Attach the second bracket to the corresponding position on the opposite side of the Secure Router 4134.
Installing the chassis 35 WARNING Risk of injury The Secure Router 4134 weighs approximately 25 lb (11.34 kg) with one power supply and the fan tray installed. To prevent injury, keep your back straight and lift with your legs, not your back. WARNING WARNUNG Verletzungsrisiko Der Secure Router 4134 wiegt mit einem Netzteil und dem Lüftereinsatz ungefähr 11,34 kg (25 lb). Um Verletzungen zu verhindern, halten Sie den Rücken gerade und heben Sie nicht mit dem Rücken, sondern den Beinen.
Installing the Secure Router 4134 chassis and hardware components • • • • Ensure you have a Phillips screwdriver #2. • Ensure your installation site meets the physical, electrical, and environmental requirements described in “Environmental requirements” (page 61). Site location is important for the proper operation of the Secure Router 4134. Place the unit in a clean, dry environment with adequate air circulation. Allow 2 to 3 feet (0.61 to 0.
Grounding the chassis 37 Prerequisites • Ensure you have the terminal lug and the associated screws and washers that shipped with the Secure Router 4134 chassis (two 8-32 x .187” pan head screws with external tooth washer). • • Ensure you have a Phillips #2 screwdriver. • Ensure you have a sufficient length of 8 AWG copper wire for the ground lead. • Attach a UL listed terminal, suitable for your equipment rack, to the end of the ground wire.
Installing the Secure Router 4134 chassis and hardware components CAUTION ACHTUNG Stellen Sie als allgemeine Sicherheitsmaßnahme sicher, dass der Wechselstrom durch einen Trennschalter auf dem Geräteträger fließt. For more information, see the guidelines presented in Articles 110-16, 110-17, and 110-18 of the National Electric Code, ANSI/NFPA 70. Procedure steps Step Action 1 Insert available ground wire in the ground lug (provided).
Installing the interface modules 39 Installing the interface modules Install the optional interface modules in the front panel of the Secure Router 4134 chassis. Nortel strongly recommends that you power down the Secure Router 4134 if you are installing an interface module in a slot in which you have not previously installed that module type. If you do not power down the router to install a module, you must reboot the router to use the card.
Installing the Secure Router 4134 chassis and hardware components Figure 3 Slot numbering legend printed on the Secure Router 4134 Slots 1 to 4 are Small Module slots. Slots 5 to 7 are Medium Module slots. If you insert a Large Module, it spans slots 6 and 7. If you install a Large Module, slots 6 and 7 become slot 6. For detailed information about the Secure Router 4134 modules, see Nortel Secure Router 4134 Installation — Hardware Components (NN47263-301).
Installing the interface modules 41 CAUTION Risk of equipment damage Always handle interface modules by the edges, or use the levers, where applicable. CAUTION ACHTUNG Risiko eines Geräteschadens Berühren Sie Interfacemodule immer an den Rändern, oder verwenden Sie die Hebel, sofern vorhanden. Prerequisites • Ensure you have a Phillips #2 screwdriver. Installing a Small Module Use the procedure in this section to install a Small Module in the Secure Router 4134.
Installing the Secure Router 4134 chassis and hardware components 4 Push gently, but firmly, to seat the connector on the interface module in the chassis back panel. 5 Use a Phillips screwdriver to tighten the two captive screws to secure the module to the chassis. --End-- Installing a Medium Module Use the procedure in this section to install a Medium Module in the Secure Router 4134. You can install Medium Modules in slots 5, 6, and 7.
Installing the interface modules 43 2 Loosen the captive screw at the top of the center slot module guide. 3 Remove the center slot module guide. The following figure shows the removal of the center slot guide. 4 Align the Large Module with the slot and the slot module guides on the outside edges of the slot. 5 Slide the module into the chassis until its connector panel touches the chassis back panel.
Installing the Secure Router 4134 chassis and hardware components The following figure shows the slot numbering on the Voice Carrier Medium Module—slot numbers are printed on the module, as well. Figure 4 Voice Carrier Medium Module slot numbering For detailed information about the Voice Carrier Medium Module, see Nortel Secure Router 4134 Installation — Hardware Components (NN47263-301).
Installing the interface modules 45 CAUTION Risk of equipment damage Always handle interface modules by the edges, or use the levers, where applicable. CAUTION ACHTUNG Risiko eines Geräteschadens Berühren Sie Interfacemodule immer an den Rändern, oder verwenden Sie die Hebel, sofern vorhanden. CAUTION If you do not install a module in the slot, be sure to keep the metal cover plate in place over the slot. Removing the cover plate impedes airflow and proper cooling of the unit.
Installing the Secure Router 4134 chassis and hardware components 5 Use a Phillips screwdriver to tighten the two captive screws that secure the Small Module to the Voice Carrier Medium Module.
Connecting power cables 47 Procedure steps Step Action 1 Insert the female end of an appropriately rated AC power cord in the AC receptacle on the rear panel of the Secure Router 4134, as shown in the following figure. 2 Insert the male end of the power cord in a standard 110/220 V AC power outlet. CAUTION Ensure you use an appropriately rated AC power cord only. Do not use an extension cord.
Installing the Secure Router 4134 chassis and hardware components Figure 5 Secure Router 4134 DC power supply terminal block Average time to install one DC power cable: 3 minutes. CAUTION ESD Always wear an ESD-preventative wrist strap when you connect cables or perform maintenance on a Secure Router 4134. Ensure that the wrist strap makes contact with your skin.
Connecting power cables 49 CAUTION ACHTUNG Stellen Sie als allgemeine Sicherheitsmaßnahme sicher, dass der Wechselstrom entweder durch eine Sicherung oder einen Wechselstromsicherung mit maximal 12 A fließt. Prerequisites • Ensure you have 18 AWG copper wire with appropriate terminal (lug). You require two wires for single source power, and four wires for redundant power supplies (that is, two wires for each input). • • Ensure you have a Phillips #2 screwdriver.
Installing the Secure Router 4134 chassis and hardware components 3 Remove the terminal cover to expose the terminal block. 4 Insert the –48 V lead behind the –48 V terminal, as shown in the following figure. Nortel Secure Router 4134 Quick Start NN47263-100 02.01 Standard 18 February 2008 Copyright © 2007, 2008 Nortel Networks .
Connecting power cables 5 Tighten the –48 V terminal to hold the lug and wire in place. The maximum tightening torque for terminal screws is 9 in-lb (1.02 N-m). 6 Insert the +48 V return lead behind the RTN terminal, as shown in the following figure. 7 Tighten the RTN terminal to hold the lug and wire in place. The maximum torque for tightening terminal screws is 9 in-lb (1.02 N-m). 8 Place the terminal cover over the terminal block. 9 Replace the terminal cover screws.
Installing the Secure Router 4134 chassis and hardware components Powering up the router Use the procedure in this section to power up your Secure Router 4134. Prerequisites • • • Ensure all installation procedures are complete. Ensure an operator console is connected to the Secure Router 4134. Ensure the Secure Router 4134 is connected to a power source. Procedure steps Step Action 1 For an AC power supply, press the rocker switch located on the power supply to the on position ( | ).
Verifying a successful installation 53 Table 3 Secure Router 4134 LED behavior at power-up Front panel LEDs Rear panel LEDs Description SYS Illuminate red, and then green FAN Illuminate red, and then green PS0 and PS1 Illuminate green for each power supply module that is installed. SM and MM Illuminate green if Small and Medium Modules are installed. The MM LED also monitors a Large Module, if installed.
Installing the Secure Router 4134 chassis and hardware components Nortel Secure Router 4134 Quick Start NN47263-100 02.01 Standard 18 February 2008 Copyright © 2007, 2008 Nortel Networks .
. Configuring the Secure Router 4134 for remote access You must connect a local terminal and log on to the Secure Router 4134 to initially configure the system. Connecting a terminal for local access You use the console port to initially configure the system. The following figure shows the location of the console port on the rear panel of the Secure Router 4134.
Configuring the Secure Router 4134 for remote access Prerequisites • • Ensure you have the supplied console cable. • Ensure you have the Secure Router 4134 securely installed in the equipment rack. • Ensure you have powered up the terminal or PC. Ensure you have the supplied female DB-9 to RJ-45 adapter if you require it for connection to your terminal or PC.
Establishing remote access 57 The following procedure uses Ethernet port 0/0 (on the rear of the Secure Router 4134) for the management port. You can also use port 0/1 or port 0/2 on the front panel of the Secure Router 4134 for management purposes. Ethernet port 0/0 is a 10/100 Base-T port. Ethernet ports 0/1 and 0/2 are 10/100/1000 Base-T ports.
Configuring the Secure Router 4134 for remote access Procedure steps Step Action 1 To access configuration mode, enter: configure terminal 2 To access the SSH key generation subtree, enter: ssh_keygen 3 To generate the DSA key, enter: generate dsa 4 To generate the RSA key, enter: generate rsa 5 To exit the SSH key generation subtree, enter: exit 6 To enable the SSH connection, enter: ssh_server enable 7 To save the configuration, enter: save local --End-- You can now access and configur
Changing the default administrator password 3 Enter the default password: setup The Secure Router 4134 prompts you for the new password. 4 Enter your new password. The Secure Router 4134 prompts you to verify the new password. 5 Re-enter your new password. A message appears that confirms that the password is changed. --End-- Nortel Secure Router 4134 Quick Start NN47263-100 02.01 Standard 18 February 2008 Copyright © 2007, 2008 Nortel Networks .
Configuring the Secure Router 4134 for remote access Nortel Secure Router 4134 Quick Start NN47263-100 02.01 Standard 18 February 2008 Copyright © 2007, 2008 Nortel Networks .
. Appendix Environmental requirements The Secure Router 4134 must operate within the specified tolerance limits shown in Table 4 "Environmental requirements for the Secure Router 4134" (page 61). ATTENTION Install the Secure Router 4134 in a restricted-access location. Limit access to the Nortel Secure Router 4134 to authorized service personnel only. Ensure you allow 2 to 3 feet (0.61 to 0.
Environmental requirements Table 4 Environmental requirements for the Secure Router 4134 (cont’d.) Parameter Range Storage humidity 0 to 95% R.H. (noncondensing) Vibration Packaging and shipping – ISTA 2A Office Vibration – GR-63-CORE Issue 3, Section 4.4.2 and 5.4.2 Acoustic noise GR-63-CORE Issue 3, section 4.6 and 5.6 Nortel Secure Router 4134 Quick Start NN47263-100 02.01 Standard 18 February 2008 Copyright © 2007, 2008 Nortel Networks .
. Appendix Translations of safety messages Class A device caution statement CAUTION This device is a Class A product. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to take whatever measures may be necessary to correct the interference at their own expense. CAUTION ACHTUNG Dies ist ein Gerät der Klasse A. Bei Einsatz des Geräts in Wohngebieten kann es Störungen des Radio- und Fernsehempfangs verursachen.
Translations of safety messages CAUTION CUIDADO Este dispositivo é um produto Classe A. Operar este equipamento em uma área residencial provavelmente causará interferência prejudicial; neste caso, espera-se que os usuários tomem as medidas necessárias para corrigir a interferência por sua própria conta. CAUTION ATTENZIONE Questo dispositivo è un prodotto di Classe A.
Overcurrent warning statement WARNING AVISO Apenas profissionais de atendimento técnico qualificados devem realizar a instalação. Leia e siga todos os avisos e instruções destacados no produto ou que façam parte da documentação. WARNING AVERTISSEMENT L’installation doit être effectuée exclusivement par un personnel qualifié. Lisez et conformez-vous à tous les avis et instructions d’avertissement indiqués sur le produit ou dans la documentation.
Translations of safety messages WARNING WARNUNG Die Nutzung dieses Produkts setzt einen Überstromschutz am Gebäude voraus. Stellen Sie sicher, dass eine Sicherung oder ein Trennschalter mit höchstens 120 V Wechselstrom, 15 A USA (240 V Wechselstrom, 10 A international) bei den Außenleitern verwendet wird. WARNING ADVERTENCIA Este producto depende de la instalación del edificio en cuanto a la protección de sobrecorriente. Asegúrese de utilizar un fusible o disyuntor no mayor a 120 V AC, 15 A EE.UU.
Power cord warning statement 67 CAUTION ACHTUNG Wenn Sie in kein Modul in diesem Steckplatz installieren, stellen Sie sicher, dass sich die Abdeckplatte aus Metall weiterhin über dem Steckplatz befindet. Wenn die Metallplatte entfernt wird, behindert dies den Luftstrom und eine angemessene Kühlung der Einheit. CAUTION ATTENTION Si vous n’installez pas de module dans le connecteur, veillez à laisser le panneau de protection métallique en place sur le connecteur.
Translations of safety messages DANGER GEFAHR Verwenden Sie nur Netzkabel mit Erdungspfad. Ohne einen angemessenen Untergrund besteht für die Person, die den Schalter berührt, die Gefahr eines Stromschlags. Das Fehlen eines Erdungspfads beim Schalter führt möglicherweise zu überhöhten Emissionen. DANGER DANGER Utilisez uniquement des cordons d’alimentation possédant un conducteur de terre. En l’absence d’un conducteur de terre, une personne touchant le commutateur pourrait recevoir un choc électrique.
Nortel Secure Router 4134 Quick Start Copyright © 2007, 2008 Nortel Networks All Rights Reserved. Release: 10.1 Publication: NN47263-100 Document status: Standard Document revision: 02.01 Document release date: 18 February 2008 To provide feedback or to report a problem in this document, go to www.nortel.com/documentfeedback. www.nortel.com The information in this document is subject to change without notice.