IP Telephone User Guide LIP-6830 SIP (Session Initiation Protocol) Sylantro SIP4B Please read this manual carefully before operating your set. Retain it for future reference. LGN-6830-1224SS01.
LIP-6830 User Guide Regulatory & Safety Notice LIP-6830D This equipment complies with the following regulatory standards, FCC Part 15, IC (Industry Canada) CS03, TBR21, TBR03, and TBR04. Also, this equipment complies with the safety requirements of UL60950, CSA60950, EN60950, EN55022 and EN55024 FCC Compliance Statement This device complies with part 15 of the FCC Rules for a Class B device.
LIP-6830 User Guide Table of Contents 1. Introducing the LIP-6830 ...................................................................1 1.1 1.2 1.3 2. LIP-6830 Overview.............................................................................................1 LIP-6830 Features .............................................................................................1 LIP-6830 General Description ............................................................................
LIP-6830 User Guide 1. Introducing the LIP-6830 1.1 LIP-6830 Overview LIP-6830 is an Internet Protocol (IP) phone designed to support hosted telephony services over a managed IP network.
LIP-6830 - 1.3 User Guide Call Return Station-to-Station dialing Handset, Headset, Speakerphone, and Ring Volume control LCD Contrast Control Call Hold Ringback Hands-free dialing Label for Programmed feature buttons Full Duplex Speakerphone Multiple Ring types Distinctive Ring tones G.723.1A / G.
LIP-6830 User Guide Figure 2. LIP-6830 buttons Number 1 2 3 4 5 Button Function Left direction button. When appears in the bottom-left corner of the LCD, the previous menu may be selected. Right direction button. When ¼ appears in the bottom-right corner of the LCD, the next group of Softkeys may be selected. Softkeys. Softkeys are interactive, changing function based on the LIP Phone status. When selected and verified, by pressing the [ OK ] Softkey, the LIP Phone performs the selected function.
LIP-6830 Number User Guide Button Function Speaker button. Toggle the LIP-6830 speakerphone On and Off. 8 9 Volume control button. Use to adjust Ring, Headset, Handset, and Speaker volume.
LIP-6830 User Guide 2. Using Basic LIP-6830 Features The LIP-6830 is equipped with Softkeys and two direction buttons, used to navigate and select items from the display menu. An item can be selected when it is displayed by using the Softkeys. In some cases, either the Softkeys or a feature button may be used to access basic features such as Conference. The Softkeys are also employed to access the ‘Advanced Services’ to which your company has subscribed.
LIP-6830 2.2 User Guide Making a Call You can make a call using on-hook or off-hook dialing. To place a call: 1) Lift the handset, press , press , or press Line button. 2) Dial the destination phone number; when the called party answers, begin speaking (the LCD will display the elapsed time of the call). To end the call: 1) Replace the handset, press 2.3 , press , press [EndC] Softkey, or press Line button.
LIP-6830 User Guide To transfer an active call: 1) Press [BXfr] Softkey. 2) Dial the number you wish to transfer. 3) Hang up to complete the transfer. 2.6 Call Forward Call forward directs incoming calls to ring at another location. There are 4 conditions that can be defined to forward calls; - Call Forward Busy — redirects incoming calls if the Line is busy. Call Forward No Answer — redirects incoming calls if the call is not answered in the designated time allowed (No Answer time).
LIP-6830 User Guide receive a call waiting tone and the caller’s number is displayed so you know who is calling before you interrupt the current call; you can choose to pick up the call, or ignore it. To answer a second call: 1) Press [Answ] Softkey; the first call is automatically placed on hold. To place a second call: 1) Place the active call on hold. 2) Press [NewC] Softkey to obtain dial tone, and dial the destination phone number.
LIP-6830 User Guide 2.12 Speed Number Dialing Within the Phone Book menu, you can set a Speed Number (00 to 99) for each Phone Book record. The Speed Number can then be used to automatically dial the telephone number for the record. Speed Number dialing must be enabled for use (refer to the Installer Guide for steps to configure the Speed Number feature). To make a call using Speed Number: 1) Dial the Speed Number (00-99) for the desired number, or lift the handset and dial the desired Speed Number.
LIP-6830 User Guide 2) Press a Line button with a solid or flashing red LED, the display indicates the number of messages waiting for that Line. 3) Press the [DIAL] Softkey and follow the voice instructions. NOTE: To access your voice mailbox, the VMS address must be configured in the LIP Phone (refer to the Installer Guide for the steps to configure the VMS address). 2.16 Shared Call Appearance / Bridge Line Appearance The LIP-6830 can support up to 24 Lines, each associated with its own button.
LIP-6830 User Guide Direct Station Selection (DSS) — one-touch calling to covered extensions, and the ability to pick up calls ringing at those extensions. Busy Lamp Field (BLF)—visual status indication of covered extensions. The DSS/BLF feature in the LIP-6830 uses the Shared call appearance feature. Operation of the DSS/BLF Coverage button however is distinctively different than a Shared Line. To call an idle covered extension: 1) Lift the handset, press , press , or press your Line button.
LIP-6830 User Guide 3. Advanced Services and the LIP-6830 LCD Menu This section describes how to view and use the Advanced Services available through the LCD menu. The Main Menu components and order of display may be different on your phone based on the service subscription. The LIP-6830 is equipped with Softkeys and two direction buttons, used to navigate and select items from menus.
LIP-6830 User Guide 1) Press the Phone Book button. 2) The Phone Book will display the first entry. Phone Book (Page 1) >1.LG-Nortel, 1305 [Prev] [Next] [Dial] ¼ To call a number listed in the Phone Book: 1) Dial the digit preceding the desired log item, or use the [Prev]-[Next] Softkeys to display additional log items. 2) Press [Dial] Softkey. To add a record to the Phone Book: 1) Press the Phone Book button. 2) Press the ¼ to view the next menu selections.
LIP-6830 User Guide 4) Edit the Name, Number and Speed Number for the record, selecting the [ OK ] Softkey for each entry (use the [Mode] Softkey to enter characters). Phone Book : Number [1] 9876 [ » ] [Mode] [ OK ] ¼ To delete a record: 1) Press the Phone Book button. 2) Select the desired record. 3) Press the ¼ to view the [Del] selection. Phone Book (Page 1) >[01]Tom,1234 [Edit] [Add ] [Del ] ¼ 4) Select [Del ] Softkey and [Yes ].
LIP-6830 User Guide Search for: [1] Tom [ » ] [Mode] [ OK ] ¼ 4) Enter the search criteria and select [ OK ] to view the search results Phone Book (Page 1) >(15)Tommy,9876 [Edit] [Add ] [Del ] ¼ 3.3 Call Park You can park a call on an internal extension. To park a call: 1) Press [Park] Softkey during conversation. 2) Enter an extension number and press the [ OK ] Softkey. Input Extension [1] [ Å ] [Mode] [ OK ] Æ 3.
LIP-6830 User Guide Input Extension [1] [ Å ] [Mode] [ OK ] Æ 3.6 Group Call Pick Up Call pick up by group is a business phone feature that lets the user pick up a call ringing at an extension in the user’s call group. User call groups are assigned in the Call Server. To pickup a call ringing at a group extension: 1) Press the ¼ to locate the [GPic] Softkey. 2) Press [GPic] Softkey. 3.
LIP-6830 User Guide NOTE: The LIP Phone must be enabled for ACD (refer to the Installer Guide for the steps to enable the ACD function). To deactivate ACD for a Line: 1) Press the ACD Agent button. 2) Press the Line button to deactivate ACD. 3) Use the backspace key to delete the Group ID. 4) Select the [ OK ] Softkey. To activate ACD operation for a Line and check-in to an ACD group: 1) Press the assigned “ACD Agent” button. ACD Status (Line 1) Check-Out [C.
LIP-6830 User Guide ACD Status (Line 1) Available [Unvl] [COut] [PRIM] ¼ To check-out of the ACD group: 1) Press the “ACD Agent” button. 2) Press Line button. 3) Press the [COut] Softkey. NOTE: The check-out Softkey is only available if the Agent is checked in. ACD Status (Line 1) Unavailable [Avail] [COut] [PRIM] To set the Line as the Primary ACD Line to display the ACD status from the LCD: 1) In the ACD menu, select the [PRIM] Softkey and press the [ OK ] Softkey. ACD Status (Line 1) Check-Out [C.
LIP-6812 June 07
LIP-6812 LGN-6830-1224SS01.
