User's Manual

ManualsBrandsNortek Security & Control ManualsElectronicsSecurity/Remote Control Transmitter

TRANSMITTER MOUNTING ADJUSTING MAGNET HEIGHT

OPTION JUMPER POSITIONS CONNECTING EXTERNAL CONTACTS

PROGRAMMING RECEIVER CHANGING THE BATTERY

• The radios are required to comply with IC Rules and Regulations. As such, they have limited transmitter power and therefore

limited range.

• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on

or near their operating frequencies, regardless of code settings.

• Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these

facts should be communicated to the ultimate users.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two

conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur

de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) This device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures.

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Any changes or modiﬁ cations not expressly approved by the party responsible for compliance could void the user’s authority

to operate the equipment.

This device conforms to Industry Canada’s rules. Any changes to the equipment, not expressly approved by Linear LLC, could

void the user’s authority to operate the equipment.

Cet appareil est conforme aux règlements de l’Industrie Canada. Tout changement à l’équipement, sans le consentement

exprès de Linear LLC, peut résulter à l’annulation de l’autorité conﬁ ée à l’usager d’opérer cet équipement.

WHEN THE SYSTEM INDICATES A

LOW BATTERY FOR THE TRANSMITTER,

REMOVE THE OLD BATTERY AND REPLACE

IT WITH A FRESH TYPE 2450 3-VOLT

COIN CELL BATTERY

BE SURE TO INSTALL THE BATTERY

WITH THE PLUS SIDE UP !!!

TEST THE SYSTEM AFTER

CHANGING THE BATTERY

WIRE EXTERNAL NORMALLY CLOSED

CONTACTS TO THE SCREW TERMINALS

PLACE JUMPER ON PINS 2 & 3

FOR EXTERNAL CONTACT ONLY

REMOVE THE JUMPER TO USE BOTH

INTERNAL AND EXTERNAL CONTACTS

NOTE: THE INTERNAL AND EXTERNAL

CONTACTS ARE IN SERIES. BOTH NEED

TO BE

CLOSED TO RESTORE THE TRANSMITTER

REMOVE SEALING PLUG

AND ROUTE WIRES

THROUGH SLOT IN

BOTTOM OF CASE

WIRE MULTIPLE EXTERNAL

CONTACTS IN SERIES

JUMPER ON 1 & 2 SELECTS

INTERNAL MAGNETIC SWITCH

INTERNAL EXTERNAL BOTH

JUMPER ON 2 & 3 SELECTS

EXTERNAL SWITCH TERMINALS

NO JUMPER SELECTS BOTH THE

INTERNAL MAGNETIC SWITCH AND

THE EXTERNAL SWITCH TERMINALS

1. PLACE RECEIVER INTO

PROGRAM OR "LEARN" MODE

2. PRESS THE TRANSMITTER'S

TEST BUTTON

3. ACTIVATE TRANSMITTER BY

OPENING DOOR OR WINDOW

4. VERIFY THAT THE RECEIVER

ACCEPTED THE SIGNAL

5. REPLACE TRANSMITTER COVER

WHEN FINISHED

OPEN DOOR, THE TRANSMIT

INDICATOR SHOULD LIGHT

NOTE: THE TRANSMIT INDICATOR

WILL ONLY LIGHT DURING

TRANSMISSIONS FOR TWO

MINUTES AFTER PRESSING THE

TEST BUTTON

NOTE: THE CASE MUST BE CLOSED

TO LEARN INTO THE RECEIVER

(IT WON'T LEARN IN IF TRANSMITTER

IS IN TAMPER MODE)

ADJUST MAGNET

HEIGHT UNTIL

CASE LEVELS

ARE ABOUT EQUAL

TRANSMITTER

CASE BOTTOM

MAGNET

THE SNAP-ON MAGNET SPACER

CAN BE USED TO ADD 1/4" HEIGHT

TO THE MAGNET (SPACERS CAN ALSO

BE SNAPPED TOGETHER FOR MORE LIFT)

ATTACH TRANSMITTER AND MAGNET

USING THE SCREWS OR THE

DOUBLE-STICK TAPE PROVIDED

NOTE: ATTACHING THE TRANSMITTER WITH DOUBLE-STICK

TAPE IS NOT ALLOWED IN UL INSTALLATIONS

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,DXS-36AF - LINEAR P/N: 232812 X4 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1 - SIDE 2 OF 2