User's Manual

ManualsBrandsNortek Security & Control ManualsElectronicsWireless Motion Sensor

BATTERY INSTALLATION & PROGRAMMING PET IMMUNITY TIPS MOUNTING PIR WITHOUT INSTALLATION BRACKETS

MOUNTING PIR WITH INSTALLATION BRACKETS PROGRAMMING WALK TESTING AND OPERATIONAL TESTING

BATTERY REPLACEMENT SPECIFICATIONS LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12) months. This

warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal

distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from

their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the

part of Linear LLC for consequential damages arising out of or in connection with use or performance

of this product or other indirect damages with respect to loss of property, revenue, or proﬁ t, or cost of

removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability

and implied warranties for ﬁ tness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu

of all other warranties express or implied.

All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear

Technical Services at 1-800-421-1587 for an RPA# and other important details.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and ﬁ ll an important need in portable wireless

signaling. However, there are some limitations which must be observed.

• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15

devices. As such, they have limited transmitter power and therefore limited range.

• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals

that occur on or near their operating frequencies, regardless of code settings.

• Changes or modiﬁ cations to the device may void FCC compliance.

• Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or

dealer, and these facts should be communicated to the ultimate users.

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,NAPPIR01 - P/N:187-1132 AX1 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - SIDE 2 OF 2

PET SIZE

JUMPER

15K = 33 LBS.

25K = 55 LBS.

SENSITIVITY

JUMPER

USE LOWEST

SETTING FOR

MAXIMUM

PET WEIGHT

ALWAYS SET

TO LOW FOR

PETS

To take full advantage of the NAPPIR01 pet

immunity features in installations with pets, use

these following steps:

• Mount the PIR with the center of the lens 7-1/2

to 8 feet above ﬂ oor level.

• Set the SENSITIVITY jumper to the LOW

position.

• Set the PET SIZE jumper to the lowest setting

for the maximum pet weight.

• Mount the PIR where pets cannot come within

six feet of the unit by climbing on furniture,

boxes, or other objects.

• Do not aim the PIR at stairs or furniture, boxes,

or other objects that can be climbed by pets.

• NOTE: The NAPPIR01 will provide immunity

to false alarms for an individual animal or a

group of animals whose total weight is equal

to or less than 55 pounds when the room

temperature is above 50° F and below 90° F.

If the optional mounting bracket is used, it

should be mounted with no tilt.

OBSERVE BATTERY POLARITY!!!

PREPARE THE RECEIVER TO

"LEARN" THE TRANSMITTTER

WHEN THE RECEIVER IS READY,

INSTALL THE CR123A 3-VOLT

LITHIUM BATTERY AS SHOWN

PIR WILL SEND A TRANSMISSION

TO THE RECEIVER AND THE

TRANSMITTER'S ID WILL

BE STORED IN THE RECEIVER

CORNER MOUNTING

WITH CORNER

BRACKET

7.5 FEET

ABOVE THE

FLOOR

7.5 FEET

ABOVE THE

FLOOR

WALL MOUNTING

WITH WALL

BRACKET

ATTACH REAR OF

CASE TO THE

PIR BRACKET

- OR -

SECURE PIR

BRACKET WITH

SCREW AND WASHER

7.5 FEET

ABOVE THE

FLOOR

CORNER MOUNT

REAR CASE WITH

FOUR SCREWS

- OR -

WALL MOUNT

REAR CASE

WITH TWO

SCREWS

PRESS WALK TEST

BUTTON ON LEFT

SIDE OF CASE

RED WALK TEST INDICATOR

WILL SHOW THROUGH PIR LENS

UNIT WILL STAY IN

WALK TEST MODE

FOR FIVE MINUTES

WALK ACROSS BEAM PATTERN

WHILE OBSERVING THE

WALK TEST INDICATOR

SNAP CASE

CLOSED BEFORE

WALK TESTING

AFTER WALK TESTING, TEST

THE PIR WITH THE SYSTEM

CONTROL PANEL OR RECEIVER

OUTPUTS: FAULT, RESTORE, LOW BATTERY, STATUS, & TAMPER

TRANSMITTER FREQUENCY: 319.5 MHz

SUPERVISORY INTERVAL: 65 MINUTES

SENSOR TYPE: QUAD ELEMENT

PET IMMUNITY: SELECTABLE: 15 Kg (33 LBS.) OR 25 Kg (55 LBS.)

SENSITIVITY JUMPER: SELECTABLE: HIGH OR LOW

SUGGESTED MOUNTING HEIGHT: 7.5 FT. (2.3 m)

SENSOR RANGE: 30 FT. (9.1 m) X 50 FT. (15.2 m)

MAXIMUM HORIZONTAL SENSING ANGLE: 90°

DIMENSIONS: 3.2” x 2.5” x 1.9” (8.12 x 6.35 x 4.82 cm)

WEIGHT (INCLUDING BATTERY & BRACKET): 3.7 OZ. (104.9 g)

COLOR: WHITE

OPERATING TEMPERATURE: 32° TO 103° F (0° TO 39° C)

RELATIVE HUMIDITY: 5-95% NON-CONDENSING

BATTERY (INCLUDED, NOT INSTALLED): ONE (1) PANASONIC CR123A,

OR EQUIVALENT LITHIUM BATTERY

REGULATORY LISTINGS: FCC PART 15, INDUSTRY CANADA

INCLUDED ACCESSORIES: MOUNTING BRACKETS AND SCREWS, PLASTIC

WALL ANCHORS

THIS DEVICE COMPLIES WITH FCC RULES AND REGULATIONS AS PART 15 DEVICES, AS WELL AS INDUSTRY

CANADA RULES AND REGULATIONS. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS

DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE

RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur

de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement.

INSTALL CR123A 3-VOLT

LITHIUM BATTERY AS SHOWN

OBSERVE

BATTERY

POLARITY!!!

WHEN THE SYSTEM INDICATES THAT THE

PIR HAS A LOW BATTERY, REMOVE THE

OLD BATTERY AND DISPOSE OF IT PROPERLY

WARNING!

IMPROPER HANDLING OF LITHIUM

BATTERIES MAY RESULT IN HEAT

GENERATION, EXPLOSION OR FIRE

WHICH MAY LEAD TO PERSONAL

INJURIES. REPLACE WITH ONLY

TYPE CR123A BATTERY.

WARNING!

BATTERY MUST NOT BE RECHARGED,

DISASSEMBLED, OR DISPOSED OF

IN A FIRE. DISPOSAL OF USED BATTERIES

MUST BE MADE IN ACCORDANCE WITH THE

WASTE RECOVERY AND RECYCLING

REGULATIONS IN YOUR AREA.

WARNING!

KEEP BATTERY AWAY FROM SMALL

CHILDREN. IF BATTERY IS SWAL-

LOWED, PROMPTLY SEE A DOCTOR

CALIFORNIA ONLY: THIS PERCHLORATE WARNING

APPLIES ONLY TO MANGANESE DIOXIDE LITHIUM

CELLS SOLD OR DISTRIBUTED ONLY IN CALIFOR-

NIA, USA. PERCHLORATE MATERIAL: SPECIAL

HANDLING MAY APPLY,

SEE: www.dtsc,ca,gov/hazardouswaste/perchlorate.

For a detail programming guide, the instruction manual should be consulted for

that panel. The below guide should only be used as a reference and not as a

replacement for using the programming instructions.

1. Enter Panel Programming

2. Select Zone #

3. Enter 6 Digit ID number (located on back of unit)

4. Enter Check sum (0-9 ; A-F) (located on back of unit). Digit that follows ¨:¨ on

the Serial ID. For A - F use 0 - 5 (See Below)

5. Enter Point ¨3¨ - for PIR

6. Push On/Off to Save

Alpha Numeric Conversion

A = *0 D = *3

B = *1 E = *4

C = *2 F = *5

NOTE: LET PIR STAND WITH NO INTERFERENCE FOR

FIRST 3 MINUTES.