User's Manual

ManualsBrandsNortek Security & Control ManualsElectronicsTransceiver Module

2GIG-XCVR5e

Transceiver

Module

PRODUCT DESCRIPTION

The Model 2GIG-XCVR5e Transceiver Module is designed to

be used with the 2GIG security system control panel. The

transceiver is a dual frequency device. It receives 345MHz

signals from the system sensors, and receives and transmits

900MHz signals to and from the Image Sensor 3.

To use a Image Sensor 3 with the 2GIG GC2e security system

control panel, the 2GIG-XCVR5e Transceiver Module must be

installed into the control panel.

The control panel must also be running rmware

Version1.23 or greater to function with the transceiver

and Image Sensor. Check the current version number of the

rmware using the control panel’s toolbox feature.

If the control panel needs a rmware update, contact 2GIG for

details on obtaining a compatible control panel or to receive

an over-the-air update through the control panel’s cell radio (if

the panel is cell radio equipped).

COMPONENT LOCATIONS REMOVE POWER

REMOVE EXISTING RECEIVER TRANSCEIVER INTO 3-PIN CONNECTOR TRANSCEIVER INTO 5-PIN CONNECTOR ANTENNA PLACEMENT

RECONNECT BATTERY TEST SYSTEM LIMITED WARRANTY

This Nortek Security & Control LLC product is warranted against defects in material and workmanship for

two (2) years. This warranty extends only to wholesale customers who buy direct from Nortek Security

& Control LLC or through Nortek Security & Control LLC’s normal distribution channels. Nortek Security

& Control LLC does not warrant this product to consumers. Consumers should inquire from their selling

dealer as to the nature of the dealer’s warranty, if any.

There are no obligations or liabilities on the part of Nortek Security & Control LLC for consequential

damages arising out of or in connection with use or performance of this product or other indirect

damages with respect to loss of property, revenue, or prot, or cost of removal, installation, or

reinstallation. All implied warranties for functionality, are valid only until the warranty expires. This Nortek

Security & Control LLC Warranty is in lieu of all other warranties expressed or implied.

IMPORTANT!!!

Radio controls provide a reliable communications link and ll an important need in portable wireless

signaling. However, there are some limitations which must be observed.

• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as

Part 15 devices. As such, they have limited transmitter power and therefore limited range.

• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by

radio signals that occur on or near their operating frequencies, regardless of code settings.

• Changes or modications to the device may void FCC compliance.

• Infrequently used radio links should be tested regularly to protect against undetected

interference or fault.

• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale

distributor or dealer, and these facts should be communicated to the ultimate users.

This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference and (2) this device must

accept any interference received, including interference that may cause undesired operation.

FCC/IC Statements

RF Exposure Considerations

This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

RF Exposure - This device is only authorized for use in a mobile application. At least 20 cm of separation

distance between the module and the user’s body must be maintained at all times.

A label must be afxed to the outside of nal commercial product with the following statements:

This device contains FCC ID: EF400207

This device contains IC ID: 1078A-00207

Consistent with §2.909(a), the following text must be included within the user’s manual or operator

instruction guide for the nal commercial product.

This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This device is only authorized for use in a mobile application. At least 20 cm of separation distance

between the module and the user’s body must be maintained at all times.

The nal host/module combination may also need to be evaluated against the FCC Part 15B criteria for

unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. The

FCC Part 15 Statement shall be included in the user manual of nal commercial product if applicable.

CAUTION: Any changes or modications not expressly approved could void the user’s authority to operate

the equipment

or dial

PRINTER’S INSTRUCTIONS:

INSTR,XCVR5e,2GIG - LINEAR P/N: 10029872 Rev-B X1 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - SIDE 1 OF 2

900 MHZ

ANTENNAA

PLUG-IN

TRANSCEIVERR

MODULE

FOAM PRESSURE PAD

SHIELD

THE ANTENNA PLACEMENT IS CRITICAL

FOR PROPER OPERATIONN

DO NOT BEND THE ANTENNA !!!

IMPORTANT !!!

BEFORE PROCEEDING, UN-PLUG THE AC POWER

SUPPLY, OPEN THE CONTROL PANEL CASE, THEN

DISCONNECT THE BACKUP BATTERY

PULL UP ON THE PLUG-IN RECEIVER MODULE TO

5-PIN

CONNECTOR

3-PIN

CONNECTOR

DISCONNECT IT FROM THE 5-PIN AND 3-PIN CONNECTORS

CONTROL

PANEL

THE PLUG-IN RECEIVER MODULE IS

LOCATED ON THE MAIN CIRCUIT BOARD,

RIGHT BEHIND THE HOME BUTTON

RECEIVER

MODULE

RE-CONNECT THE BATTERY, CLOSE THE CONTROL

PANEL, THEN PLUG IN THE AC POWER SUPPLY

PLACE THE CONSOLE IN

PROGRAMMING MODE

AND PREPARE IT FOR WIRELESS

ZONE PROGRAMMING.

REFER TO THE IMAGE SENSOR’S

INSTALLATION GUIDE.

2GIG GC2e CONSOLE

IMAGE SENSOR

USE THE CONTROL PANEL'S TOOLBOX TO CHECK THE

FIRMWARE VERSION IN THE CONTROL PANEL. THE FIRMWARE

VERSION MUST BE 1.23 OR GREATER BEFORE PROCEEDING.

INSERT THE TRANSCEIVER PARTWAY

INTO THE 3-PIN CONNECTOR

BE CAREFUL TO ALIGN ALL THE

PINS INTO THE CONNECTOR.

INSERT THE TRANSCEIVER

INTO THE 5-PIN CONNECTOR

BE CAREFUL TO

ALIGN ALL THE PINS

INTO THE CONNECTOR !!!

PRESS DOWN ON

FOAM PRESSURE PAD

TO SEAT THE XCVR2

THE ANTENNA PLACEMENT IS

CRITICAL FOR PROPER OPERATION

DO NOT BEND THE ANTENNA!

THE ANTENNA SHOULD BE

AT THIS ANGLE AFTER

TRANSCEIVER INSTALLATION

Only compatible with the GC2e panel.

Installation

Instructions

Compatible Devices

• eSeries 345 sensors

• Legacy 345 sensors

• Image Sensor 3

Summary of content (2 pages)

PAGE 1
2GIG-XCVR5e PRODUCT DESCRIPTION COMPONENT LOCATIONS The Model 2GIG-XCVR5e Transceiver Module is designed to be used with the 2GIG security system control panel. The FOAM PRESSURE PAD transceiver is a dual frequency device. It receives 345 MHz signals from the system sensors, and receives and transmits 900 MHz signals to and from the Image Sensor 3. Only compatible with the GC2e panel. PRINTER’S INSTRUCTIONS: INSTR,XCVR5e,2GIG - LINEAR P/N: 10029872 Rev-B X1 - INK: BLACK - MATERIAL: 20 LB.
PAGE 2
GIG-XCVR5e DESCRIPTION DRODUIT Seulement compatible avec le panneau GC2e. PRINTER’S INSTRUCTIONS: INSTR,XCVR5e,2GIG - LINEAR P/N: 10029872 Rev-B X1 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.