Installation Instructions

If you are going to use the 1051 transmitter in a safety
related device, be sure to read the manufacturer’s
instructions with regard to wiring and limitations of the safety circuit.
After you have wired and coded the 1051, you are now
ready for mounting. You will note that there are four holes
in the case, through which you can mount your screws,
rivets, or other mounting devices. If the transmitter is to be
used in th
e proximity of metal, be sure to test the location at
the greatest distance the device will be from its receiver, in
order to be sure that adequate performance is achieved.
ANY METAL, INCLUDING MOUNTING PLATES, ETC., MAY
AFFECT THE PERFORMANCE OF YOUR TRANSMITTER.
Once you are satisfied with the performance of the radio,
you can permanently mount it.
Nortek Security & Control LLC has taken every
precaution to a sure thas t the 1051
will perform reliably.
In order to provide the greatest reliability, we have fastened the printed circuit board to the case with a
special fastening agent, such as Loctite . We suggest that you use a similar material to your fastening screws if
vibration is likely to be encountered.
…
IMPORTANT SAFETY TEST
…
Before releasing the radio transmitter for use, test the system for
proper operation after installing the radio transmitter and
associat
ed hardware. The system should be tested at various
positions of travel of the gate member to be certain that the gate
edge, radio transmitter, receiver and gate operator are
functioning to detect an obstruction and reverse or stop the
gate.
MAINTENANCE
The 1051 Transmitter needs a minimum of care,
however, certain precautions must be taken: 1. Be sure to check the 1051 Transmitter as a system. Be
sure that the device that is connected to the 1051 is
funct ioning wit h th e tra ns mi tter, and with t he
receiver.
2. Check the system to which the 1051 is attached fre-
quently.
3. The 1051 employs long life Alkaline-Manganese Dioxide
Batteries (Eveready Energizer 522 or equivalent). Nominal
life for these batteries is three years, but we suggest you
test the unit more often than this. Test the transmitter any
time you perform maintenance on the
rest of the system.
WARRANTY
MULTI-CODE products products carry an eighteen (18) month
warranty against defects in workmanship or material. This
warranty begins at the date of manufacture, for eighteen
months. Nortek Security & Control LLC warrantees our
product only to our authorized dealers and distributors, and
not to the end customer. If you have questions about our
warranty, please ask your dealer to determine the nature
and scope of his warranty. Nortek Security & Control LLC
does not assume, and is not responsible for, any real or
consequential damages from claims against the performance of our product, nor is it liable for any costs related to loss of life, properly, or revenue. Further, Nortek Security & Control LLC is in no way responsible for installation of our product, and will assume no costs to reinstallation or removal. Nortek Security & Control LLC’s Warranty is in lieu of all other warrantees, ex-pressed, or implied.
PLEASE NOTE Nortek Security & Control LLC has devoted a great deal of
time and research in order to provide the most reliable
equipment possible. Certain limitations must be observed.
1.
MULTI-CODE radio components must conform with FCC Part 15 requirements. For this reason, the range and power of our radios is within specified limits.
2.
As with all manufacturers, MULTI-CODE radios
must accept all signals that they receive. This may, in rare instances, create difficulty.
INSTR,INSTL,MC1051,GATE XMTR
LINEAR P/N: 216977_Rev-AX1
INK: BLACK
MATERIAL: 20 LB. MEAD BOND
SIZE: 7.500" x 7.500"
SCALE: 1-1
SIDE 2 OF 2
TERMINAL B LOCK
MTG. HOLE
BATTERY
MTG. HOLE
MTG. HOLE
MTG. HOLE
CODE SWITCH
STRAIN RELIEF
TM