Installation Instructions

SAFETY EDGE
3. You should test your entire system occasionally in
order to be sure that all components are working in
good order.
4. Nortek Security & Control LLC’s dealers can provide
you with information regarding the use of our radio
controls, and can provide valuable installation and
operation information, when requested.
WARNING: Changes or modifications not expressly approved by the manufacturer could void the user’s anthority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
For service, return to your dealer or shop prepaid to:
7_Rev-AX116972 Nortek Security & Control LLC 0202 © thgirypoC
Model 1051
Important! Read
Before Installation
The MULTI- CODE 1051 transm itter has been
designed to provide great reliability and safety, but it must be installed correctly. Read the enclosed instructions
carefully.
The Model 1051 may be used for a variety of purposes,
and wherever remote signaling is desirable, as specified by FCC regulations. If this transmitter is to be used in an application which may be safety related be sure to take
special precauti
ons. Nortek Security & Control LLC
has
taken every step to insure the best possible product, but
you must be certain to install the 1051 transmitter correctly.
Before installing the 1051 transmitter,
open it up by
removing the four screws which secure the top of the case.
You will note that there is a terminal block (see figure 1), to
which you will secure the wires coming from your device.
Run your wire through the strain relief
fitting, leaving
enough wire to provide adequate length for stripping.
YOUR WIRE SHOULD BE 18 TO 24 GAUGE, although any wire that fits snugly in the strain relief fitting may be used.
Be sure to check the water-tightness of the fitting if you use anything other than 18-24 gauge wire, as this may
compromise the integrity of the case. Put your two wires
under the terminal blocks, and fasten by screwing dow
n.
Next, code your transmitter and, if necessary, your
receiver. The code switch (see figure 1) allows for 1024 possible combinations. If you have an existing receiver, you
may code the 1051 to the same code, or you may choose to
wire a separate receiver. If you wire a second receiver, be
sure to separate the two receivers as much as possible, to
avoid any possibility of interference.
INSTR,INSTL,MC1051,GATE XMTR
LINEAR P/N: 216977_Rev-AX1
INK: BLACK
MATERIAL: 20 LB. MEAD BOND
SIZE: 7.500" x 7.500"
SCALE: 1-1
SIDE 1 OF 2
®
Multi-Code
USA & Canada [phone] & [phone]
[phone] - Toll Free FAX [phone]
www.nortekcontrol.com
• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC & IC Notice This device complies with Part 15 of the FCC Rules and Industry Canada license exempt standard(s). Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and 2) This device must accept any interference received, including
interference received that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1) l’appareil ne doit pas produire de brouillage, et 2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
TRANSMITTER