Installation Instructions

INSTR,INST,DNT00053A / DNT00054A Linear P/N: 10027318 Rev-A Material: 20 Lb. Mead Bond Size: 8.500" x 11.000" Ink: Black Scale: 1-1 Side 2 of 2
STEP 5
Review memory. Press and hold the receiver’s
program button (channel one or two) until the LED begins to flash
(about 3 seconds) and then release the button. Count the number
of flashes. The number of flashes equals the number of
transmitters programmed into that channel of the receiver.
NOTE: Don’t hold down the programming button longer than
5 seconds, the receiver’s memory for that channel will be
erased (Step 7).
STEP 6
Test receiver.
Be sure door area is clear.
Activate
each transmitter. The receiver relay should click (relay output
models only) and the operator should activate. Wait 2 seconds
between each activation.
STEP 7
Erasing receiver memory. Transmitters may be
erased from the receiver’s memory by pressing and holding the
receiver’s program button (channel one or two) for 5 seconds or
more. After the LED blinks (count of transmitters) it will blink one
more time for channel one and twice for channel 2 as the
receiver’s memory for that channel is erased. All transmitters
for each receiver channel are erased at the sa
me time.
INFO 1A
Opening battery compartment. To access the
transmitter’s batteries remove the battery access screw on the
back of the unit. Flip the unit over so that the front is facing you.
Use a small screwdriver to open the battery compartment.
INFO 1B
Replacing transmitter batteries. Replace the two
batteries with two Type 2032 lithium batteries or equivalent. The
batteries stack on top of each other with the (+) sides facing the
front of the transmitter. Replace with new batteries then close the
battery compartment, replace battery access screw and test
transmitter.
INFO 2
Visor Clip Removal. The visor clip can be removed
by removing the three screws as shown. Slide the clip off the
retaining plate and reattach the plate to the transmitter.
NOTE: The same transmitter (or the same transmitter button on
multi-button transmitters) cannot be programmed into both
receiver channels 1 and 2.
NOTE: If the receiver’s LED flashes continuously when a
transmitter isn’t being activated, the receiver is too close to an
electrical noise source. Move the receiver away from the noise
source or call technical services for assistance.
LIMITED WARRANTY
This product is warranted to the consumer against defects in material and
workmanship for one year from the date of purchase. This warranty applies
to first retail buyers of new devices. Warrantor will repair, or at its option,
replace, any device it finds that requires service under this warranty, and
will return the repaired or replaced device to the consumer at the
warrantor’s cost. For warranty serv
ice and shipping instructions contact
warrantor at the address shown below. Devices must be sent to warrantor
for service at owner’s expense. The remedies provided by this warranty
are exclusive. Implied warranties under state law are to the one year period
of this written warranty. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitation may not apply to you.
In
order to be protected by this warranty, save your proof of purchase and
send copy with equipment should repair be required. This warranty gives
you specific legal rights, and you may also have other rights which vary
from state to state.
All products returned for warranty service require a Return Product
Authorization Number (RPA#). Contact Linear Technical Services at
1-800-421-1587 for an RPA# and othe
r important details.
WARNING!
BE SURE DOOR
AREA IS CLEAR
OF OBSTRUCTIONS
PRESS TRANSMITTER
BUTTON TO TEST
CH2
CH1
CH2
CH1
PRESS PROGRAM BUTTON
(CHANNEL 1 OR 2)
FOR FIVE SECONDS OR MORE
LED WILL FLASH, COUNTING THE
TOTAL NUMBER OF TRANSMITTERS
PROGRAMED TO THAT CHANNEL.
THEN IT WILL BLINK ONE MORE TIME
AS THE TRANSMITTERS ARE ERASED
FROM THAT CHANNEL
REMOVE BATTERY
ACCESS SCREW
REPLACE
WITH TWO
TYPE 2032
BATTERIES
SIDE UP
CH2
CH1
CH2
CH1
PRESS PROGRAM BUTTON
(CHANNEL 1 OR 2)
FOR THREE SECONDS
THEN RELEASE
LED WILL FLASH, COUNTING THE
TOTAL NUMBER OF TRANSMITTERS
PROGRAMED TO THAT CHANNEL
REMOVE VISOR CLIP
BY REMOVING THREE
SCREWS
CH2
CH1
CONTINUOUSLY FLASHING LED MAY
INDICATE ELECTRICAL NOISE
INTERFERRENCE
20
3
2
SWING BATTERY
COMPARTMENT OPEN
FLIP
TRANSMITTER
OVER
Copyright © 2019 Nortek Security & Control LLC 10027318 Rev-A
FCC & IC Notice
This device complies with Part 15 of the FCC Rules and Industry Canada license exempt standard(s). Operation is subject to the
following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference received that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
1) (1) l’appareil ne doit pas produire de brouillage, et
2) (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
WARNING:
equipment.