Installation Instructions

Copyright © 2019 Nortek Security & Control LLC 209420 C
DTKP
DIGITAL KEYPAD
TRANSMITTER
Installation
Instructions
USA & Canada [phone] & [phone]
[phone] - Toll Free FAX [phone]
www.nortekcontrol.com
DESCRIPTION
The Delta-3 DTKP Keypad is one of Linear’s series of wireless
radio controls designed for use with automatic garage door
and gate operators. The Delta-3 radio format provides 256
different codes.
In operation, the user enters their unique code on the unit’s
keypad and presses the START/STOP button to activate the
door operator. For up to 30 seconds after the last activation,
the DTKP can be re-triggered by simply pressing the START/
STOP button again. This allows the user to stop or reverse the
opener quickly, without having to re-enter their code.
The DTKP has built-in keypad lighting for use at night or in
entering their code (or pressing START/STOP twice at any
time), the user can light up the keypad.
The clear silicone keys are back-lit with a pleasing green
glow. Standard Digital receivers are programmed by setting
an a-position dipswitch in the receiver. The DTKP will match
the receiver’s code when the correct number keys are
pressed before the START/STOP key. The correct code for
the DTKP matches the “ON” positions of the receiver_
The code must be entered in descending order. Keys O
and 9 are not used on the DTKP. A keypad lockout timer will
disable the keypad after 3 code entry attempts. The keypad
must remain idle for 30 seconds before new attempts can
be made.
STEP 1: Check receiver’s code. Locate the coding dipswitch
on the receiver. On some receivers (Model DR), the switch is
hidden when the receiver is mounted on the door operator.
Loosen the three terminal screws to remove the receiver and
examine the coding switch. From 8 to 1, write down the
numbers of all the “ON” switch positions.
SWITCHES IN
RECEIVER
THIS SWITCH
HAS 6, 3 & 2 ON
DTKP CODE
FOR THIS
RECEIVER:
DAYTIME OPERATION
NIGHTTIME OPERATION
PRESS:
USER'S SECRET CODE
PRESS:
USER'S SECRET CODE
LIGHTS
KEYPAD
PRESS:
LIGHTS
KEYPAD
RECONNECT RECEIVER TO GARAGE DOOR OPERATOR
STEP 2: Verify Receiver Installation. Be sure the receiver
is reconnected (if removed) to the garage door operator as
described in the receiver’s Installation Instructions.
STEP 3: Test receiver. Be sure door area is clear. Try the
keypad code. Enter a digit for each receiver switch “ON”
position in descending order. The operator should activate
when the START/STOP button is pressed after entering the
valid keypad code.
ENTER CODE
AND PRESS
START/STOP
WARNING!
BE SURE DOOR
AREA IS CLEAR
OF OBSTRUCTIONS
STEP 4: Mount Keypad. Use the two screws and screw
anchors provided to mount the keypad to the wall. Be sure the
keypad, cover the screw heads using the two plugs supplied.
STEP 5: Operation keystrokes. See the illustration for
examples of daytime and nighttime operation.
USE SCREW
ANCHORS
PROVIDED
COVER SCREWS
WITH PLUGS
MOUNT
KEYPAD
TO WALL
INFO 1A: Opening battery compartment. The DTKP battery
should last up to 5 years with normal use. To remove the
battery door to replace the battery, remove the battery door
retaining screws and slide the battery door off.
INFO 1B: Replacing battery. Remove the low battery and
replace it with a fresh 9-volt alkaline or lithium battery.
Replace the battery door and retaining screws.
REMOVE
RETAINING
SCREWS AND
BATTERY DOOR
REPLACE
WITH 9-VOLT
ALKALINE OR
LITHIUM
BATTERY ONLY
LIMITED WARRANTY
This Nortek Security & Control LLC product is warranted against defects in material
and workmanship for twenty-four (24) months. This warranty extends only to
wholesale customers who buy direct from Nortek or through Nortek’s normal
distribution channels. Nortek Security & Control LLC does not warrant this product to
consumers. Consumers should inquire from their selling dealer as to the nature of the
dealer’s warranty, if any. There are no obligations or liabilities on the part of Nortek
Security & Control LLC for consequential damages arising out of or in connection with
use or performance of this product or other indirect damages with respect to loss of
warranties, including implied warranties for merchantability and implied warranties
Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Authorization Number
(RA#). Contact Nortek Security & Control Returns at 1-855-546-3351 for an RA# and
other important details.
IMPORTANT !!!
need in portable wireless signaling. However, there are some limitations which
must be observed.
• For U.S. installations only: The radios are required to comply with FCC Rules
and Regulations as Part 15 devices. As such, they have limited transmitter
power and therefore limited range.
• A receiver cannot respond to more than one transmitted signal at a time
and may be blocked by radio signals that occur on or near their operating
frequencies, regardless of code settings.
• Infrequently used radio links should be tested regularly to protect against
undetected interference or fault.
• A general knowledge of radio and its vagaries should be gained prior
to acting as a wholesale distributor or dealer, and these facts should be
communicated to the ultimate users.
FCC & IC Notice
This device complies with Part 15 of the FCC Rules and Industry Canada license
exempt standard(s). Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference
received that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
1) l’appareil ne doit pas produire de brouillage, et
2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
WARNING:
could void the user’s authority to operate the equipment.
PRINTER’S INSTRUCTIONS:
INSTR,INST,DTKP - P/N: 209420 C - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - TOLERANCE +/- .125” SCALE: 1-1
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC)
rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.