User's Manual

ManualsBrandsNortek Security & Control ManualsElectronicsWireless Siren & Strobe

CONFIGURATION

The WA105DBZ-1 supports the Conﬁ guration command. The WA105DBZ-1 can

be conﬁ gured to operate slightly differently than how it works when you ﬁ rst

install it. Using the Conﬁ guration command you can conﬁ gure the following:

Parameter 0: Siren / Strobe Mode

By default, the siren and strobe on the WA105DBZ-1 will activate when turned

on. To activate the Siren only, set parameter 0 to 1. For strobe only set to 2.

• Parameter No: 0

• Length: 1 Byte

• Valid Values = 0 (default) or 1 or 2. Default is 0.

Parameter 1: Auto Stop Time

By default the auto stop time is 30 seconds. Setting parameter 1 to 1 will

increase the time to 60 seconds. Changing it to 2 will increase the stop time to

120 seconds. Setting the stop time to 3 will turn off the auto stop and will require

a command from the Controller to turn off.

• Parameter No: 1

• Length: 1 Byte

• Valid Values = 0 or 1 or 2 or 3. Default is 0.

Default Setting

Each conﬁ guration Parameter can be set to its default setting by setting the

default bit in the Conﬁ guration Set command. See your controller’s instructions

on how to do this (and if it supports it).

All conﬁ guration commands will be reset to their default state when the

WA105DBZ-1 is excluded from the Z-Wave network by using the controller to

reset the node.

SPECIFICATIONS

Power Supply 100 - 240 VAC, 50/60 Hz

Power Supply Output 12 V, 1A

Battery Backup 6V NiMH, 150 mAH (5 day operation

with no alarms)

Frequency 908.42 MHz

Audible Alarm 105 dB

Strobe White LED with red lens

Operating Temp 5°F~140°F / -15°C~ 60°C

Repeater Ye s

Range Up to 100 feet line of sight between

the Z-Wave Controller and/or the

closest Z-Wave Repeater

INTEROPERABILITY WITH Z-WAVE DEVICES

A Z-Wave network can integrate devices of various classes, and these devices

can be made by different manufacturers, just as the WA105DBZ-1 can be

incorporated into existing Z-Wave networks.

PACKAGE CONTENTS

• WA105DBZ-1 with Wall mounting bracket

• AC Adapter

• Foam mounting tape

• 2x mounting screws

• Installation Manual

REGULATORY INFORMATION

The WA105DBZ-1 is certiﬁ ed to comply with applicable FCC and IC rules and regulations governing

RF and EMI emissions.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference

received, including interference received that may cause undesired operation.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected

• Consult the dealer or an experienced radio/TV technician to help.

• Changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment

IC Notice

This Class B digital apparatus complies with Canadian ICES-003

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le présent

appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire

de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si

le brouillage est susceptible d’en compromettre le fonctionnement.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Operation is

subject to the following two conditions: (1) this device may not cause interference, and (2) this device

must accept any interference, including interference that may cause undesired operation of the device.

WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12) months.

This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s

normal distribution channels. Linear does not warrant this product to consumers. Consumers should

inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations

or liabilities on the part of Linear Corporation for consequential damages arising out of or in

connection with use or performance of this product or other indirect damages with respect to

loss of property, revenue, or proﬁ t, or cost of removal, installation, or reinstallation. All implied

warranties, including implied warranties for merchantability and implied warranties for ﬁ tness, are valid

only until Warranty Expiration Date as labeled on the product. This Linear LLC Warranty is in lieu of

all other warranties express or implied. All products returned for warranty service require a Return

Product Authorization Number (RPA#). Contact Linear Returns at 1-855-546-3351 for an RPA# and

other important details.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and ﬁ ll an important need in portable

wireless signaling. However, there are some limitations which must be observed.

• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as

Part 15 devices. As such, they have limited transmitter power and therefore limited range.

• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by

radio signals that occur on or near their operating frequencies, regardless of code settings.

• Changes or modifications to the device may void FCC compliance.

• Infrequently used radio links should be tested regularly to protect against undetected interference

or fault.

• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale

distributor or dealer, and these facts should be communicated to the ultimate users.

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,WA105DBZ-1; LINEAR P/N: P2065 X4; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; SCALE: 1-1; PAGE 2 OF 2