User's Manual

3
e
o
t
r
n
e
e
y
a
e
e
r
e
.
n
e
g
r
t
,
e
d
Z-WAVE PROGRAMMING
Adding to a Network:
Refer to your Controller operating instructions to add this device under the
command of the Wireless Controller.
6. With your Controller in Discovery or Add Mode, press the LEARN button.
The green indicator will blink slowly.
7. When the Smart Flow Detector is added, the green indicator will blink
quickly three times, then stay on.
8. You should see an indication on your Controller that the “device was added”
to the network and the green indicator will turn off.
9. The device will appear in the list of sensors at the hub.
If the Controller/Gateway shows the addition failed, the red indicator will fl ash
three times then stay on. If this occurs, repeat Steps 1-3.
✓ NOTE: If you have trouble adding the WL00Z-1 to a group it may be that
the Home ID and Node ID were not cleared from it after testing. You must
fi rst “RESET UNIT” to remove it from the network. Although adding it to a
group includes it in the network, removing it from a group does not remove it
from the network. If removed from a group, it functions as a repeater (only).
“RESET UNIT” removes it completely from the network.
To Reset Unit (If Required):
In the event that your primary Controller is lost or otherwise inoperable, to reset
the WL00Z-1 and clear all network information, follow these steps:
1. Press the LEARN button fi ve (5) times quickly. The green indicator will start
to blink quickly.
2. Immediately press and hold the CALIBRATION button for 15 seconds.
3. The green indicator will turn off when the reset is successful.
Removing from a Network:
The WL00Z-1 can be removed from the network by the Controller/Gateway.
Refer to the Controller operating instructions for details.
1. Set the Controller into Removal Mode.
2. Press the LEARN button.
3. The green indicator will begin to blink slowly. When the Smart Flow Detector
is successfully removed, the green indicator will blink quickly three times
then stay on.
4. You should see an indication on your Controller that the device was removed
from the network.
✓ NOTE: If the Controller/Gateway shows the remove failed, the red indicator
will fl ash three times and stay on. If this occurs, repeat Steps 1-3.
CONFIGURATION
The WL00Z-1 supports the Confi guration command. It can be confi gured to
operate slightly differently than how it works when you fi rst install it.
Using the Confi guration command you can confi gure the following:
Flow Detection Alert Timing
By default, the WL00Z-1 will send an alert after approximately 21 minutes of
continuous water fl ow.
The length of time for continuous water fl ow before an alert is sent can be
set to a minimum of 14 minutes and a maximum of 350 minutes by using the
Confi guration Command Class, Parameter 0.
By default, the WL00Z will send an alert when water is running from 21 to
27minutes.
Parameter Length Valid Values Confi guration Option
0
2
Bytes
2 to 50
in whole
number
increments.
Default =3
Alert is sent when water is
fl owing for x 7 + 7minutes
Associations
The WL00Z-1 supports one level of Z-Wave association.
Group 1 association is used to identify another Z-Wave device in the network
that will receive unsolicited state changes and notifi cation (alarm) events.
For instructions on how to “set lifeline association” please refer to your wireless
controller instructions.
INDICATOR LEGEND
GREEN
INDICATOR
RED
INDICATOR
DESCRIPTION
Solid Off
Powered on with no error conditions.
(Note: the unit can be uncalibrated and/or
unpaired in this state)
Blinks every
second
Off
Indicates the WL00Z-1 is in the process
on Learning or Unlearning into a Z-Wave
network.
Fast blink
(200ms) for
3 seconds,
then Solid
Off
Indicates the WL00Z-1 succeeded Learning
or Unlearning into a Z-Wave network.
Super fast
(100ms) blink
Off
This is the result of tapping the Learn
button 5 times within 2 seconds to initiate a
Z-Wave reset of the WL00Z-1
This is the fi rst step, the second step is to
then hold down the Calibrate button for 15
seconds.
If the Calibrate button is not held down
during this state, it will end after 5 seconds.
Solid
Blink every
second
The WL00Z-1 detects water fl owing.
Blink every
400ms,
alternately
with Red LED
Blink every
400ms,
alternately
with Green
LED
Indicates the WL00Z-1is in the process of
Calibration.
Off Solid
Indicates the last action performed by
the WL00Z-1 failed. This can be Learn or
Unlearn into the Z-Wave network, or a failed
Calibration.
Off
Blink every
second
The WL00Z-1detects water fl owing, after the
last action performed by the WL00Z-1 failed.
Off
Fast blink
(200ms) for
3 seconds,
then Solid
Indicates the WL00Z-1 failed Learning or
Unlearning into a Z-Wave network.