User's Manual

2 Copyright © 2014 Linear LLC
10 OntheGo!Bridge,pressandreleasethelearnbutton(thisisthe
small,blackplasticbuttonontheLEDsideoftheGo!Bridgebelow
the900MHzLED).ThistransmitsthedeviceIDtothecontrolpanel.
Whenthe“lear
nopera
tionsucceeded”messageappearsandthe
paneldisplaystheType(Go!Bridge)andID#,theGo!Bridgeand
panelarelinked.The900MHzLEDontheGo!Bridgealsoflashes
GREEN.
11 AtthePairwithXcvrDevicepage,tapOK.Thentap↓tocontinue
withConfiguringtheGo!BridgeSetti
ngsbelow.
Configuring the Go!Bridge Settings
Toco
nfiguretheGo!Bridgeset
tings:
1 AttheQ:SelectConfigurationSource(0to1)screentap→to
selectthe(0)DHCPsetting.ThisassignstheGo!BridgeanIP
Addressonthelocalnetwork.ItisrecommendedthatyoutapNext
toskipsteps2‐3andcontinuewithstep4.
2 Ifyoutap↓(insteadofNext)instep1above,theQ:SelectPort#
(1to8)pageappears.En
tertheportnumberforthethird‐party
monitoringservices’server.Thentap↓.
3 AtQ:Used(0to1),tap→toselectoneoftheseoptions:
• (0)Disabled(Recom
mended).Thisisthedefaultsetting.Then
tapNextandskiptostep4.
OR
• (1)Enabled.Thentap↓.AttheQ:Ent
erPortValue(0‐65535)
screen,tap↓toacceptthedefaultportvalue.Next,attheQ:
EnterPortForwardIPAddressscreen,tap↓toacceptthe
addressconfiguredbytheprovider.Youcanconfigureupto
eight(8)ports.Ifyouar
efinishedconfi
guringports,tapNext.
4 AttheSummaryofNetworkDevicepage,tap↓.Verifythelistof
portnumbersandforwardIPaddressesappearsasprogrammed.
ThentapSkip.
5 AtQ93EnterBroadbandNetworkFailureTime(1to255),enter
thedesirednumberofminutesthatmustpassbeforeanetwork
failuretriggersthecontrolpaneltoissueatroublealert.The
defaultvalueis30minutes.Thentap↓.
NOTE: Atroublealertconsistsofanaudi blebeepandthecontrol
panel’sHomescreendisplaysatroublemessage.
6 AtQ94SelectBroadbandNetworkFailureReport(0or1),tap→
toselectwhetherornottoreportthebroadbandnetworkfailure
tothemonitoringservice:
• (1)Ena
bled.Thisisthedef
aultsetting.Networkfailuresare
reportedtomonitoringservice.
OR
• (0)Disabled.Network
failuresarenotreported.
7 TapEnd.
8 AttheSummaryofSystemConfigurationpage,verifythesettings.
ThentapSaveChanges.
9 TapExittotheclosetheSystemConfiguration.
LED Indicators
ThetablebelowdetailstheLEDcolorsfortheGo!Bridge:
Verifying the Settings
InadditiontoverifyingthesettingsafterconfiguringtheGo!Bridge,
youcanalsoverifythesettingsatanytimeasfollows:
1 AtthecontrolpanelHomescreen,tapSecurity.
2 TapMenu.
3 TapToolbox.
4 IntheEnterYourCodetoAccesstheToolboxpage,enterthe
mastercode.
5 Tap→toscrolltotheToolbox(3of3)page.ThentapGo!Bridge
Status.
Asummarypagedisplaysthefo
llowinginformation:
• NetworkConf
iguration.TheDHCPconfigurationsource.
• IPAddress.TheIPAddr
essfortheGo!Bridge.Thisisa32‐bit
numericaddressthatidentifiesthedeviceonthenetwork.
• SubnetMask.Thesubnetmaskfo
rthenetwork.Alldevices
thatarejoinedtoanetworkbelongtoasubnetwork.
• Ga
teway.TheIPAddr
essfortheaccesspointtotheexternal
network.Typically,thisistheIPAddressofthelocalnetwork
routerornodethatcontroltrafficforyourISP.
• MACAddre
ss.ThisistheMediaAccessControl(MAC)Address.
ItisaphysicaladdressthatisencodedtotheGo!Bridgeduring
themanufacturingprocess.
Testing
TheGo!Bridgeteststhenetworkconnectiontothethird‐party
monitoringservice.AreportshowsifGo!Bridgehassuccessfully
connected(orfailedtoconnect)totheexternalserver.
Registration
ToregistertheGo!Bridgewiththemonitoringservice,refertoyour
specificprovider’sregistrationinstructions.
SPECIFICATIONS
HousingMaterial ABSplasticandpoly‐carbonate
Color White
LEDs Internetand900MHz
Dualcolor(REDandGREEN)
Dimensions(LxWxD) 6.25x4.5x1in
Power 5‐VDCUSBMini‐BPowerS upply
Radio 25channelfrequency‐hoppingspreadspectrum,403kHz
channelspacing(910.2‐920.275MHz),GFSKmodulation,
128kbps,+19dBmmaximumRFpowerout
Ethernet 100BASE‐T
SerialtoEthernetProcessor TexasInstrumentsStellarisCortexMS
IMPORTANT NOTE
ShouldthelocalnetworkloseInternetaccessduetoapoweroutage
orinterruption,theGo!Bridgeisnotequippedwithabatterybackup
system.Tobestprepareforpowerfailuresandtoensurethesecurity
systemmaintainsInternetaccesswiththemonitoringserviceforlife‐
safetycommunicationsduringpowerfailures,thelo
calnetworkmus
t
haveadedicatedUninterruptedPowerSupply(UPS)orbatterybackup
solutionfromathird‐partymanufacturerinplace.LinearLLCdoesnot
supply,provide,recommend,ortesttheGo!BridgewithanyUPSor
batterybackupsolution.Itisalsoassumedthatowner’sInternet
ServiceProvider(ISP)maintainsaback
upbatt
ery(orpowergenerator)
fortheirremotenetworkequipment.
NetworkLED GlobeIcon
SolidGREEN Indicatesthepresenceofanexternalnetworkconnection.
FlashingGREEN NetworkcableispluggedinandIPaddressisactivelybeing
assigned.
SolidRED Networkcableunplugged.
900MHzLED IconLabeled“900MHz”
SolidGREEN Linkedandcommunicatingwiththecontrolpanel.
FlashingGREEN Linkedtothecontrolpanel.Communicationissuesexist.
SolidRED Notlinkedtothecontrolpanel,turnssolidafteradevicereset.
FlashingRED Notlinkedtothecontrolpanel.