User's Manual

ManualsBrandsNortek Security & Control LLC/2GIG ManualsElectronics2GIG-BRDG1-900

2GIG-BRDG1-900

Go!Bridge IP Communicator

INSTALL INSTRUCTIONS

TheGo!Bridge™IPCommunicator(2GIG‐BRDG1‐900)provides

Internetconnectivitybetweenthemonitoringservice’sCentralStation

andtheGo!Control®Panel(requiresthe900MHzTransceiver(2GIG‐

XCVR)).

Itsupportsautomaticfirmwareupdates,providesinteractivesecurity

services,andincreasessupervisionusingsignal‐forwardingtothe

CentralStation.Tocommunicatewirelesslywiththeco

ntrolpanel,the

900M

HzTransceiverModule(2GIG‐XCVR)mustbeinstalledinthe

panelandtheGo!Bridgemustbeconnectedtothelocalnetwork

routerusinganEthernetcable(notprovided).

Box Contents

Verifythatthepackageincludesthefollowing:

•1—Go!Bridge

•1—5‐VDCUSBMini‐BPowe

rSupply

•1—Stand

Requirements

Beforeyouinstall,program,andtesttheGo!Bridge,ensurethecontrol

panelbeingpairedwiththeGo!Bridgemeetstheserequirements:

•FirmwareVers

ion1.12(orhigher)

•2GIG‐XCVR900MHzTr

ansceiver

NOTE: Toprotectdatasentviathelocalwirelessnetwork,isit

recommendedthatyouinstalltheGo!Bridgeonalocal

networkwhereWPA(Wi‐FiProtectedAccess)orWEP(Wire

EquivalentPrivacy)Encryptionisalreadyenabled.

Afterins

talling,progr

amming,andtestingtheGo!Bridge,youwillneed

toregisteranewcustomerwiththethird‐partymonitoringservice.

SeeRegistrationonpage2.

Figure 1 Go!Bridge Front View—LED Indicators and Learn Button

Powering ON the Go!Bridge

UsethesestepstopowerONtheGo!Bridge:

1 EnsuretheGo!Bridgeisconnectedtoapowersource.

NOTE: DonotconnectanEthernetcabletotheGo!Bridgeatthis

time.Youwillconnectthecablewhencompletingthestepsin

ProgrammingtheGo!Bri

dgeint

otheControlPanel.

2 (Optional)Placethestand(provided)onacounter,desktop,or

otherflatsurface.SettheGo!Bridgeinthestand.

3 VerifythatthetwoLEDsontheGo!BridgeilluminateinRED(see

Figure1Go!BridgeFron

tView—LEDIndicatorsandLearnButton).

NOTE: Ifthe900MHzLEDilluminatesinGREEN(thelowerLED),

verifythatthenetworkcableisnotconnectedtothe

Go!Bridge.Ifthecableisdisconnectedanditisstillilluminated

GREEN,usetheendofanopenpapercliptopressandrelease

therecessedResetbutton.Thebuttonislocatedinsi

dethe

smallholeontheportsideoftheGo!Bridge,di

rectlyabove

theEthernetport.Thisrestoresthefactorysettings.SeeFigure

2Go!BridgeRe

arVi

ew—PortsandRecessedResetButton.

Figure 2 Go!Bridge Rear View—Ports and Recessed Reset Button

4 AftertheGo!BridgeispoweredON,continuewithProgramming

theGo!Bridgeint

otheControlPanel.

Programming the Go!Bridge into the Control

Panel

UsethesestepstoplacethecontrolpanelandGo!Bridgeinlearning

mode.Thisgivesthecontrolpaneltheabilitytolearnthenetwork

settingstransmittedbytheGo!Bridge.

NOTE: Toscrollbetweenoponsonthecontrolpanel,tapthe←

and→arrows.Tomovetothepreviousornextprompttapthe

↑and↓arrows.

1 ConnectanEthernetcable(notincluded)totherouterand

Go!Bridge.

2 EnsurethecontrolpanelispoweredON.ThentaptheHome 

button.

3 Tapthesystemlogointhelower‐rightcornerofthecontrolpanel

Homescreen.

4 AttheEnterYourCodepage,enteryour4‐digitinstallercodetogo

totheInstallerToolbox(page1of2)page.

5 AttheInstallerToolbox(page1of2)page,tapSystem

Configuration.

6 AttheQ1:SelectRFSensor#(01to48)page,tapGoTo. 

7 AttheEnterQuestionNumber(2Digits)page,enter92.

8 AtQ92SelectNetworkDevice(0to1),tap→toscrollto(1)

Go!Bridge.Thentap↓.

9 AtQ:NetworkDeviceID(ReadOnly),tapLearn.Thisgivesthe

paneltheabilitytodiscovertheread‐onlynetworkdeviceID

transmittedbytheGo!Bridge.

AtthePa

irwithXcvrDevicepa

ge,the“initiatinglearningprocess”

messageappears.

ANetworkLED

B 900MHzLED

CLearnbutton

ARecessedResetbutton

BEthernetport

CPowersupplyport

INSTRUCTIONS: FILE: 77-000044-001-BRDG1-900-INSTALL-INSTRUCTIONS-REVB-PRT-EN.PDF - DATE: 5/5/2014 - INK: BLACK - MATERIAL: 20 LB MEAD BOND - SIZE: 8.5"X11" - SCALE: 1 - PRINTING: FRONT AND BACK - FOLDING: FOLD TO FIT IN BOX - PAGES: 3

Summary of content (3 pages)

PAGE 1
INSTRUCTIONS: FILE: 77-000044-001-BRDG1-900-INSTALL-INSTRUCTIONS-REVB-PRT-EN.PDF - DATE: 5/5/2014 - INK: BLACK - MATERIAL: 20 LB MEAD BOND - SIZE: 8.5"X11" - SCALE: 1 - PRINTING: FRONT AND BACK - FOLDING: FOLD TO FIT IN BOX - PAGES: 3 2GIG-BRDG1-900 Go!Bridge IP Communicator INSTALL INSTRUCTIONS The Go!Bridge™ IP Communicator (2GIG‐BRDG1‐900) provides Internet connectivity between the monitoring service’s Central Station and the Go!Control® Panel (requires the 900 MHz Transceiver (2GIG‐ XCVR)).
PAGE 2
10 On the Go!Bridge, press and release the learn button (this is the small, black plastic button on the LED side of the Go!Bridge below the 900MHz LED). This transmits the device ID to the control panel. When the “learn operation succeeded” message appears and the panel displays the Type (Go!Bridge) and ID#, the Go!Bridge and panel are linked. The 900MHz LED on the Go!Bridge also flashes GREEN. 11 At the Pair with Xcvr Device page, tap OK.
PAGE 3
REGULATORY INFORMATION Wireless Product Notice Radio controls provide a reliable communications link and fill an important need in portable wireless signaling; however, there are some limitations which must be observed. • For United States Installations Only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range (approximately 400 ft.).