Owner's manual

Index I-3
G
Graphic User Interface .................................................... 1-7
H
Heater ............................... See also Heater Control Window
advanced options ....................................................... 1-6
Controlled Process Heat ............................................. 1-7
Dual Heater Control ................................................... 1-6
Idle Timers.................................................................. 1-6
loop parameters ......................................................... 9-5
mode .......................................................................... 9-6
needle heater ............................................................. 9-4
Pre Heat Timer Verification ........................................ 1-7
Rapid Response Heater System ................................. 1-6
set point ..................................................................... 9-6
settings ....................................................................... 9-6
setup ...................................................................... 4-107
temperature verification ............................................ 9-8
turning on and off ...................................................... 9-5
Heater Control Window ......................................... 9-4–9-13
Alarm tab ................................................................. 9-12
Heat Control tab ......................................................... 9-9
Input tab .................................................................. 9-10
Main tab ..................................................................... 9-6
Output tab ................................................................ 9-11
Run Time tab .............................................................. 9-7
Height Sense
batch .......................................................................... 1-5
height sense always ................................................... 1-5
options ....................................................................... 1-5
selective height sense ................................................ 1-5
Height Sensor
setup ........................................................................ 4-69
Help .............................................................. See Online Help
Help Menu .................................................................... A-14
I
Image Capture .............................................................. 4-52
Individual Setup Procedures ....................................... 4-131
Initial Setup ............................................ See Setup Routines
Installation ............................................................ See FmXP
J
Jet on the Fly ................................................................. 7-57
continuous path method ......................................... 7-57
no dispensing control mode ..................................... 7-59
non-continuous path method .................................. 7-57
position based spacing control mode ...................... 7-58
time based control mode ......................................... 7-58
total number of dots control mode ......................... 7-59
Jog Window .................................................................... 3-6
configuration ............................................................ 3-11
defining locations ..................................................... 3-12
keyboard commands ................................................ 3-10
K
Keepout Zones ............................................................ 4-112
L
Language ......................................................................... 4-2
Library Pattern ....................................... See Pattern Library
Line .................................................................................. 6-5
editing line location .................................................. 6-45
editing style and weight ........................................... 6-46
programming ............................................................ 6-13
Line Parameters ................................................... 6-28–6-37
during dispense ........................................................ 6-29
editing .............................................................. 6-35, 6-46
jetted lines ................................................................ 6-31
post dispense ............................................................ 6-30
pre-dispense ............................................................. 6-28
LMO ............................................ See Local Machine Offsets
Local Machine Offsets ............................................ 1-8, 4-24
air pressure ............................................................... 4-32
height sense origin ................................................... 4-28
maintenance ............................................................. 4-33
valve bias ......................................................... 4-29, 6-41
workpiece origin ....................................................... 4-26
Local Machine Valve Bias .............................................. 5-22
Logging .......................................................................... 4-15
automatic file deletion ............................................. 4-15
event logging ............................................................ 4-11
Trc/Dbg logging ........................................................ 4-12
Loop Block Command .................................................... 7-12
M
Machine Offsets ............................................................ 4-16
Main Program .......................................................... 5-4, 5-7
editing ....................................................................... 6-46
Main Wndow ................................................................... 3-4
Mass Flow Calibration ................. See Flow Rate Calibration
Measure Flow Rate ....................................................... 6-41
MFC ............................................ See Mass Flow Calibration
Monitored Inputs .......................................................... 4-45
Motion Commands .......................................................... 6-9
Multipass Pattern ................................................... 6-7, 7-11
timer ................................................................ 7-12,
7-14
N
Needle Heater ................................................................. 9-4
O
Offset Routines ....................................... See Setup Routines
Online Help ............................................................. 1-8, 3-26
Operation Level ........................................................ 1-8, 4-5
P
Pass Block Command .................................................... 7-12
Passthrough ..................................................................... 8-8