Owner's manual

Table of Contents xi
Figure 6-10 Programming Weight Control Lines .................................................................................. 6-18
Figure 6-11 Program1 – Workpiece Pattern ........................................................................................ 6-19
Figure 6-12 Pre-Dispense Dot Parameters .......................................................................................... 6-21
Figure 6-13 During Dispense Dot Parameters ..................................................................................... 6-22
Figure 6-14 Post Dispense Dot Parameters ........................................................................................ 6-23
Figure 6-15 Advanced Dot Parameters ............................................................................................... 6-24
Figure 6-16 Dots Program – Workpiece Pattern .................................................................................. 6-27
Figure 6-17 Pre-Dispense Line Parameters ........................................................................................ 6-28
Figure 6-18 During Dispense Line Parameters .................................................................................... 6-29
Figure 6-19 Post Dispense Line Parameters ....................................................................................... 6-30
Figure 6-20 Relationship Between the Retract Distance, Backtrack Length and Backtrack Gap ....... 6-31
Figure 6-21 Jetted Line Parameters – Pre Dispense ........................................................................... 6-31
Figure 6-22 Jetted Line Parameters – During Dispense ...................................................................... 6-32
Figure 6-23 Jetted Line Parameters – During Dispense ...................................................................... 6-33
Figure 6-24 Jetted Line Parameters – Control Tab.............................................................................. 6-34
Figure 6-25 Lines Program – Workpiece Pattern ................................................................................. 6-37
Figure 6-26 Setup Valves Dialog Box .................................................................................................. 6-38
Figure 6-27 Valve Settings Dialog Box (DP-Series, DV-Series Valves) .............................................. 6-39
Figure 6-28 Valve Settings Dialog Box (DJ Series Valves) ................................................................. 6-39
Figure 6-29 Valve Settings Dialog Box (NexJet) .................................................................................. 6-40
Figure 7-1 Program Command Sequence ........................................................................................... 7-2
Figure 7-2 Creating a Pattern ............................................................................................................... 7-3
Figure 7-3 Create Pattern Dialog Box .................................................................................................. 7-3
Figure 7-4 Placing a Pattern at Multiple Locations .............................................................................. 7-4
Figure 7-5 Placing a Pattern Edit Window ........................................................................................... 7-5
Figure 7-6 FmXP Tutorial Board - Side 2 ............................................................................................. 7-7
Figure 7-7 WCLine1 Pattern ................................................................................................................ 7-9
Figure 7-8 Placing a Pattern .............................................................................................................. 7-10
Figure 7-9 Opening a Pattern ............................................................................................................. 7-11
Figure 7-10 Multipass Workpiece ......................................................................................................... 7-11
Figure 7-11 Underfill Patterns .............................................................................................................. 7-13
Figure 7-12 Chip Offset ........................................................................................................................ 7-14
Figure 7-13 Underfill Program .............................................................................................................. 7-21
Figure 7-14 M-Pass Program ............................................................................................................... 7-28
Figure 7-15 Step and Repeat Edit Window .......................................................................................... 7-29
Figure 7-16 Step and Repeat Program ................................................................................................ 7-32
Figure 7-17 Opening a Library Pattern ................................................................................................ 7-35
Figure 7-18 Enabling Pattern Library Event Tracking .......................................................................... 7-36
Figure 7-19 RFID Configuration Dialog Box ........................................................................................ 7-38
Figure 7-20 RFID Program Association Dialog Box ............................................................................. 7-39
Figure 7-21 Creating a Program Association ....................................................................................... 7-39
Figure 7-22 Selecting the Module Definition Pattern ........................................................................... 7-41
Figure 7-23 Location Table .................................................................................................................. 7-41
Figure 7-24 Defining a Module Location .............................................................................................. 7-42
Figure 7-25 Assign Module ID Dialog Box ........................................................................................... 7-43
Figure 7-26 Camera View of the Human Readable ID ........................................................................ 7-45
Figure 7-27 Establishing the Strip Origin ............................................................................................. 7-45
Figure 7-28 Strip Columns and Rows .................................................................................................. 7-46
Figure 7-29 Strip Map Coordinate Arrangement - Origin in the Lower Left Corner ............................. 7-46
Figure 7-30 Strip Map Coordinate Arrangement - Origin in the Lower Right Corner ........................... 7-46
Figure 7-31 Strip Map Coordinate Arrangement - Origin in the Upper Left Corner ............................. 7-46
Figure 7-32 Strip Mapping Setup Dialog .............................................................................................. 7-47
Figure 7-33 Multi-Chip Module ............................................................................................................. 7-49
Figure 7-34 Fixed Speed vs. Variable Valve Speed ............................................................................ 7-50
Figure 7-35 Setup Valves ..................................................................................................................... 7-50
Figure 7-36 Valve Settings ................................................................................................................... 7-51
Figure 7-37 Creating a Table of Valve Speeds .................................................................................... 7-52
Figure 7-38 Edit Flowrate Setup for Valve Speed ................................................................................ 7-53