Manual

I-2 Index
F
Feature Access................................................................ 4-5
Fiducial Assisted Setup................................................. 4-66
Fiducials ....................................................................... 5-19
caliper tool ............................................................... 5-26
contrast..................................................................... 5-21
corner....................................................................... 5-26
editing ...................................................................... 6-37
fiducial detection methods ....................................... 5-20
model fiducials......................................................... 5-20
options ..................................................................... 7-13
re-using .................................................................... 7-13
shape ............................................................... 5-20, 5-21
size........................................................................... 5-21
teaching a corner fiducial......................................... 5-27
teaching a model fiducial ......................................... 5-22
Find Substrate Height ..................................................... 6-6
Flow Rate
measure flow rate command .................................... 6-36
parameters....................................................... 5-14, 6-35
Flow Rate Calibration.......................................... 5-14, 6-34
performing ............................................................... 6-36
Flow Rate Calibration Table................................ 7-39, 7-40
Fluid
files ................................................................... 5-2, 5-12
flow rate parameters................................................. 5-14
low fluid software solution ........................................ 1-4
pot life/low fluid check ............................................ 5-16
setup......................................................................... 5-12
FmConfig.ini.......................................................... 2-4, 4-53
FmConvIO.ini............................................................... 4-53
FmDispIO.ini................................................................ 4-53
FmNT
error messages............................................................B-1
file structure ........................................................ 2-4, 2-5
fluid files............................................................. 5-1, 5-2
heater files.................................................................. 5-1
installation package.................................................... 2-1
installation procedure................................................. 2-2
main program............................................................. 5-7
recipe .................................................................. 5-1, 5-2
standard filename conventions................................... 2-4
starting and exiting..................................................... 3-2
structure ..................................................................... 5-4
upgrade procedure...................................................... 2-3
vision files........................................................... 5-1, 5-2
workpiece pattern....................................................... 5-8
H
Heater Control Window.................................................. 9-4
alarm tab .................................................................. 9-12
heat control tab........................................................... 9-9
main tab ..................................................................... 9-6
output tab ................................................................. 9-11
run time tab ................................................................ 9-7
Heaters............................. See also Heater Control Window
advanced options........................................................ 1-6
anafaze controller....................................................... 9-4
heat output limit....................................................... 9-11
loop parameters.......................................................... 9-5
mode .......................................................................... 9-6
needle heater .............................................................. 9-4
offsets .......................................................................4-19
set point ......................................................................9-6
settings........................................................................9-6
setup .........................................................................4-48
temperature verification..............................................9-8
turning on and off.......................................................9-5
Height Sensor..................................................................1-4
setup .........................................................................4-30
Help Menu...........................................................3-26, A-10
I
Installation
procedure....................................................................2-2
J
Jet on the Fly .................................................................7-43
continuous path method............................................7-43
no dispensing control mode......................................7-45
non-continuous path method .................................... 7-43
position based spacing control mode........................7-44
time based control mode...........................................7-44
total number of dots control mode............................7-45
Jog Window ....................................................................3-6
conveyor position controls .........................................3-7
dispensing head position controls...............................3-7
K
Keepout Zones ..............................................................4-52
L
Language.........................................................................4-2
Line .................................................................................6-5
editing.......................................................................6-40
programming ............................................................ 6-12
Line Parameters.............................................................6-27
editing..............................................................6-29, 6-40
Local Machine Offsets ...........................................1-7, 4-19
Loop Block Command ..................................................7-12
Low Fluid Software Solution ................................ See Fluid
M
Machine Offsets ............................................................4-14
Main Program...........................................................5-4, 5-7
editing.......................................................................6-41
Main Wndow...................................................................3-5
Manual Run Commands................................................3-11
Manual Setup Options................................................... 4-82
Mass Flow Calibration ................See Flow Rate Calibration
Motion Commands..........................................................6-9
Multipass Pattern....................................................6-6, 7-12
timer ................................................................7-13, 7-14
Multiple Flow Rates .................... See Variable Valve Speed
N
Needle Heater..................................................................9-4
Needle Sensor
setup .........................................................................4-14