Manual

Appendix A - Programming Menu Detail A-3
Program
Program
D
ot
L
ine
A
rc
C
ircle
Coat D
ot
Coat G
rid
Coat L
ine
Dot G
rid
R
ectangle
P
ot
A
rea Fill f
ff
f
W
eight Control Line
S
tep and Repeat
C
omment
I
nstruction f
ff
f
Height Sense f
ff
f
Pattern f
ff
f
Process Commands f
ff
f
Time Commands f
ff
f
Motion f
ff
f
Send Commands f
ff
f
Conveyor f
ff
f
Library f
ff
f
Set Z Fast Mode f
ff
f
Dot
L
ine
A
rc
C
ircle
Coat D
ot
Coat G
rid
Coat L
ine
Dot G
rid
R
ectangle
P
ot
A
rea Fill f
ff
f
W
eight Control Line
S
tep and Repeat
C
omment
I
nstruction f
ff
f
Height Sense f
ff
f
Pattern f
ff
f
Process Commands f
ff
f
Time Commands f
ff
f
Motion f
ff
f
Send Commands f
ff
f
Conveyor f
ff
f
Library f
ff
f
Set Z Fast Mode f
ff
f
Program
Program
D
ot
L
ine
A
rc
C
ircle
Coat D
ot
Coat G
rid
Coat L
ine
Dot G
rid
R
ectangle
P
ot
A
rea Fill f
ff
f
W
eight Control Line
S
tep and Repeat
C
omment
I
nstruction f
ff
f
Height Sense f
ff
f
Pattern f
ff
f
Process Commands f
ff
f
Time Commands f
ff
f
Motion f
ff
f
Send Commands f
ff
f
Conveyor f
ff
f
Library f
ff
f
Set Z Fast Mode f
ff
f
Dot
L
ine
A
rc
C
ircle
Coat D
ot
Coat G
rid
Coat L
ine
Dot G
rid
R
ectangle
P
ot
A
rea Fill f
ff
f
W
eight Control Line
S
tep and Repeat
C
omment
I
nstruction f
ff
f
Height Sense f
ff
f
Pattern f
ff
f
Process Commands f
ff
f
Time Commands f
ff
f
Motion f
ff
f
Send Commands f
ff
f
Conveyor f
ff
f
Library f
ff
f
Set Z Fast Mode f
ff
f
Program Menu
1. Dot - Opens a Teach Window for programming dot
dispensing.
2. Line
- Opens a Teach Window for programming line
dispensing.
3. Arc
- Opens a Teach Window for programming arc
dispensing.
4. Circle
- Opens a Teach Window for programming circle
dispensing.
5. Coat Dot
- Used for programming dots with the flux jet valve
only.
6. Coat Grid
- Used for programming grids of lines with the flux
jet valve only.
7. Coat Line
- Used for programming lines with the flux jet
valve only.
8. Dot Grid
- Used for programming grids of dots with the flux jet valve only.
9. Rectangle
- Opens a Teach Window for programming a rectangle dispensing pattern.
10. Pot
- Opens a Teach Window for programming pot dispensing.
11. Area Fill
– Opens a drop-down menu for accessing rectangular spiral fills, circular spiral fills, and
rectangular zigzag fills.
12. Weight Control Line
- Opens a Teach Window for programming weight-control lines. Weight-
Control lines use a specific amount of fluid for each line based on Line Parameters.
13. Step and Repeat
- Used for applications that require the same pattern to be placed at multiple
locations on a single board.
For example, if you have a workpiece or an Auer boat with 10 chips aligned in rows and
columns, you can program your dispensing pattern, place the pattern in the first location,
identify the last location where the pattern should be placed, and FmNT calculates and places
the pattern at all of the other locations on the workpiece.
14. Comment
– Allows you to insert comments directly into a program.
15. Instruction
– Instructions are used mainly for testing and troubleshooting during the dispensing
program development process. You can disable or enable a single line or multiple lines within
your dispensing program to isolate problems or to try different options.
To disable a command, use the mouse or trackball to highlight the line (or lines), and then click
on
Program>Instruction >Disable Instruction.