Manualshelf

Manual

ManualsBrandsNordson ASYMTEK ManualsSoftwareFluidmove For Windows NT Ver.4.6
181182183184185186187188189190
6-18 Beginning Programming
Program1
Workpiece
1 DOT: 1, (0.977, 2.502)
2 LINE: 1, Start: (0.076, 3.848), End: (1.071, 3.847)
3 ARC: 0, 1, 0.000, (3.253, 2.680), (3.308, 2.598), (3.327, 2.503), (3.077,2.502), -45.082
4 CIRCLE: 0, 1, 0.000, (2.530, 2.573), (2.592, 2.506), (2.470, 2.504), 2.531, 2.512), -350.000
5 RECTANGLE: 1, (3.316, 3.857), (4.068, 3.353)
6 POT: 1, 20.000, (2.171, 3.418)
7 RECT SPIRAL: 0, 1, 0.200, (4.665, 3.856), (5.413, 3.353)
8 WEIGHT CONTROL: 10,000, 1, …
9END:
1
Program1
Workpiece
Program1
Workpiece
1 DOT: 1, (0.977, 2.502)
2 LINE: 1, Start: (0.076, 3.848), End: (1.071, 3.847)
3 ARC: 0, 1, 0.000, (3.253, 2.680), (3.308, 2.598), (3.327, 2.503), (3.077,2.502), -45.082
4 CIRCLE: 0, 1, 0.000, (2.530, 2.573), (2.592, 2.506), (2.470, 2.504), 2.531, 2.512), -350.000
5 RECTANGLE: 1, (3.316, 3.857), (4.068, 3.353)
6 POT: 1, 20.000, (2.171, 3.418)
7 RECT SPIRAL: 0, 1, 0.200, (4.665, 3.856), (5.413, 3.353)
8 WEIGHT CONTROL: 10,000, 1, …
9END:
1
1 DOT: 1, (0.977, 2.502)
2 LINE: 1, Start: (0.076, 3.848), End: (1.071, 3.847)
3 ARC: 0, 1, 0.000, (3.253, 2.680), (3.308, 2.598), (3.327, 2.503), (3.077,2.502), -45.082
4 CIRCLE: 0, 1, 0.000, (2.530, 2.573), (2.592, 2.506), (2.470, 2.504), 2.531, 2.512), -350.000
5 RECTANGLE: 1, (3.316, 3.857), (4.068, 3.353)
6 POT: 1, 20.000, (2.171, 3.418)
7 RECT SPIRAL: 0, 1, 0.200, (4.665, 3.856), (5.413, 3.353)
8 WEIGHT CONTROL: 10,000, 1, …
9END:
1
Figure 6-9 Program1 – Workpiece Pattern
To run a program:
1. In the Programming Window, click on
Run and select Dry Run.
2. Watch the video display as the Dispensing Head performs the programmed commands. The
camera will act as the needle and follow the lines, but no dispensing will be performed.
!You may click on the
Stop button at any time to stop the run at the end of the program.
The current board will be completed before dispensing stops.
!Click on
Abort to abort the run immediately.
WARNING! If the lines were “dry dispensed” at an incorrect angle, you may need to
reprogram the workpiece origin and workpiece angle. If so, you will also need to
reprogram the lines.