Instruction Manual

ManualsBrandsNordson ASYMTEK ManualsSoftwareFluidmove For Windows NT Ver.4.4

Index - 2

–I–

I/O, 3-10

I/O testing, 3-10

initialization, 3-1

installation, 1-1, 6-1, 6-15, 6-19, 6-20, 6-21, 6-22

Installation Package

Installation Guide, 2-1

Tutorial Board, 2-2

User Guide and Tutorial, 2-1

–J–

jog commands, 3-10, 3-11

–L–

light levels, 3-1, 7-11

light source, 7-4

lines, 8-2

parameters, 8-10

weight control, 8-5, 9-2

–M–

Main Window, 3-4, 3-5, 3-6

master offsets, 6-19, 6-20, 6-21, 6-22

measurements, 6-11

menu bar, 3-13, 3-14

menu commands, 3-13

menu restrictions, 6-13

mid-move 1 and mid-move 2, 8-13

multi shot delta, 8-12

multipass, 9-1, 9-14

–N–

needle heater, 4-1

needle sensor, 6-19, 6-20, 6-21, 6-22

needle setup, 6-19

Notepad, 6-13

number of shot, 8-12

–O–

offsets

Calculate Master Offsets, 6-15

Valve Offsets, 6-15

on-vector mode/off-vector mode, 8-13

operator level, 6-12, 6-13

Orthogonality Tolerance, 7-11, 7-12

–P–

part skipping, 3-2

passwords, 6-11, 6-12

pattern placement, 7-2, 8-24, 9-1

patterns, 7-2, 8-23

position controls, 3-18, 3-20

pot life, 3-25, 6-28, 6-31

potting, 8-21

preferences, 6-1

pre-move delay factor, 8-6

procedures, 7-2

process commands, 3-15

process toolbar, 3-15

production, 3-21, 3-25, 10-3

production lot tracking, 3-2

Production Window, 3-4, 3-21, 3-22, 3-23, 3-24

program commands, 3-16

program commands toolbar, 3-16

programming, 3-12, 7-1, 7-2, 9-1

area fill, 8-21

encapsulation, 8-21

lines, 8-1

multipass, 9-1, 9-16

underfill patterns, 9-4

weight control lines, 8-5

programming setup, 6-28, 6-30

Programming Window, 3-4, 3-12

projection length, 7-11

prompted setup, 10-3

purge station, 3-2

purging, 6-31

–R–

reticles, 6-17

retract acceleration, 8-7, 8-12

retract distance, 8-7, 8-13

retract speed, 8-7, 8-12

run production, 3-24

Run Window, 3-4, 3-24, 3-25

–S–

safe Z height, 6-19, 6-20

safety precautions, 1-1, 2-2

scale, 3-9, 6-1

SECS/GEM interface, 3-4, 3-26, 5-1, 10-1

settling time, 8-11

setup

dispensing system, 2-2, 3-6

heaters, 4-1

initial, 3-1, 6-1, 6-19, 6-20, 6-21, 6-22

Manual, 6-35

production, 3-2, 3-23, 6-1, 6-24, 10-3

programming, 6-28, 6-30

purge, 6-1

vision system, 6-15, 6-17

shutdown, 10-5

shut-off distance, 8-6

single fiducial, 7-11, 7-12

skew correction, 3-1

skip marks, 9-1

SMEMA, 10-1

software update, 6-19, 6-20, 6-21, 6-22

SPC data log, 6-13

spiral fill, 8-23

statistics, 3-2, 3-25

suckback, 8-6, 8-13

system configuration, 6-2

system setup, 6-1