User Manual
Index - 2
I
I/O, 3-10
initialization, 3-2
installation, 1-1, 6-1, 6-15, 6-19, 6-23
Installation Package
Installation Guide, 2-1
Tutorial Board, 2-2
User Guide and Tutorial, 2-1
L
light levels, 3-1, 7-13
light source, 7-5
lines, 8-2
parameters, 8-10
weight control, 8-6, 9-3
M
manual conventions, iii
master offsets, 6-19, 6-23
measurements, 6-11
menu commands, 3-13
menu restrictions, 6-13
mid-move 1 and mid-move 2, 8-14
multi shot delta, 8-13
multipass, 9-1, 9-14
N
needle heater, 4-1
needle sensor, 6-19, 6-23
needle setup, 6-20
needle-to-camera offset, 6-27
needle-to-height sensor offset, 6-26
Notepad, 6-14
number of shot, 8-13
O
offsets
Calculate Master Offsets, 6-15
camera-to-height sensor, 6-27
needle-to-camera, 6-25
needle-to-height sensor, 6-26
Valve Offsets, 6-15
on-vector mode/off-vector mode, 8-14
operator level, 6-12, 6-13
Orthogonality Tolerance, 7-13, 7-15
P
part skipping, 3-2
passwords, 6-11, 6-12
pattern placement, 7-3, 8-23, 9-1
patterns, 7-3, 8-22
pot life, 3-25, 6-34, 6-37
potting, 8-21
preferences, 6-1
pre-move delay factor, 8-7
procedures, 7-3
process commands, 3-15
production, 3-21, 3-25, 10-4
production lot tracking, 3-2
program commands, 3-16
programming, 3-12, 7-1, 7-3, 9-1
area fill, 8-21
encapsulation, 8-21
lines, 8-1
multipass, 9-1, 9-16
underfill patterns, 9-4
weight control lines, 8-6
programming setup, 6-34, 6-36
projection length, 7-14
prompted setup, 10-4
purge station, 3-2, 6-25
purging, 6-37
R
reticles, 6-17
retract acceleration, 8-8, 8-13
retract distance, 8-8, 8-14
retract speed, 8-8, 8-13
S
safe Z height, 6-19, 6-23, 6-25
scale, 3-9, 6-1
SECS/GEM interface, 3-4, 3-26, 5-1, 10-1
settling time, 8-12
setup
dispensing system, 2-2, 3-6
heaters, 4-1
initial, 3-2, 6-1, 6-19, 6-23
Manual, 6-46
production, 3-2, 3-23, 6-1, 6-41, 10-4
programming, 6-34, 6-36
purge, 6-1
vision system, 6-15, 6-17
shutdown, 10-6
shut-off distance, 8-7
single fiducial, 7-13, 7-15
skew correction, 3-1
skip marks, 9-2
SMEMA, 10-1
software update, 6-19, 6-23
SPC data log, 6-14
spiral fill, 8-22
statistics, 3-2, 3-25
suckback, 8-7, 8-14
system configuration, 6-2
system setup, 6-1
T
temperature, 4-2
terminal communication, 3-9
thaw time, 3-25
timers, 9-1, 9-5
tool tips, 3-15
TS-01 Interface Simulator, 10-1
tutorial boards, 1-1, 7-4