Manual

Table of Contents vii
Figure 4-27 Active Tool ........................................................................................................................ 4-29
Figure 4-28 Needle Finder Setup Dialog Box ...................................................................................... 4-29
Figure 4-29 Production Configuration Window .................................................................................... 4-33
Figure 4-30 Product Map ..................................................................................................................... 4-35
Figure 4-31 Product Map Configuration ............................................................................................... 4-35
Figure 4-32 Maintenance Configuration Screen .................................................................................. 4-37
Figure 4-33 Adding/Deleting Maintenance Procedures ....................................................................... 4-38
Figure 4-34 Adding a Maintenance Procedure .................................................................................... 4-39
Figure 4-35 Creating Custom Buttons ................................................................................................. 4-40
Figure 5-1 Opening a Product Program ............................................................................................... 5-2
Figure 5-2 Opening a Macro Program ................................................................................................. 5-3
Figure 5-3 Macro1.ECM ....................................................................................................................... 5-5
Figure 5-4 Reference Frames .............................................................................................................. 5-8
Figure 5-5 Program Properties ............................................................................................................. 5-9
Figure 5-6 Property Field Buttons ...................................................................................................... 5-10
Figure 5-7 New Program Dialog Box ................................................................................................. 5-11
Figure 5-8 Untitled Program ............................................................................................................... 5-12
Figure 5-9 Main Pattern Edit Frame Properties ................................................................................. 5-12
Figure 5-10 Applicator On/Off Button ................................................................................................... 5-13
Figure 5-11 Activating the Speed Limit ................................................................................................ 5-13
Figure 5-12 Setting the Speed Limit .................................................................................................... 5-14
Figure 5-13 Creating a Macro Program ............................................................................................... 5-15
Figure 5-14 Active Tool - Genie Camera ............................................................................................. 5-16
Figure 5-15 New Pattern Dialog Box ................................................................................................... 5-16
Figure 5-16 Verifying Pattern Position ................................................................................................. 5-17
Figure 5-17 Program Instruction Buttons ............................................................................................. 5-18
Figure 5-18 Pattern and Instruction Properties .................................................................................... 5-19
Figure 5-19 Camera and Vision Tab .................................................................................................... 5-21
Figure 5-20 Fiducial Instruction and Location ...................................................................................... 5-21
Figure 5-21 Fiducial Box ...................................................................................................................... 5-21
Figure 5-22 Host Control Screen ......................................................................................................... 5-22
Figure 5-23 Fiducial Score ................................................................................................................... 5-22
Figure 5-24 Fiducial Not Found ............................................................................................................ 5-23
Figure 5-25 Manual Fiducial Find ......................................................................................................... 5-23
Figure 5-26 Creating the Rectangle Pattern ........................................................................................ 5-24
Figure 5-27 Creating a Mask Region ................................................................................................... 5-25
Figure 5-28 Creating a Procedure........................................................................................................ 5-26
Figure 5-29 Naming a Procedure ......................................................................................................... 5-27
Figure 5-30 Abort Program Procedure ................................................................................................. 5-27
Figure 5-31 Ini File Write Instruction .................................................................................................... 5-28
Figure 5-32 Script Instruction ............................................................................................................... 5-28
Figure 5-33 Selecting a Pattern ........................................................................................................... 5-29
Figure 5-34 Calling a Procedure .......................................................................................................... 5-30
Figure 5-35 Cropping An Image ........................................................................................................... 5-34
Figure 5-36 Zooming In ........................................................................................................................ 5-35
Figure 5-37 Zooming Out ..................................................................................................................... 5-35
Figure 5-38 Resizing a Docked Image ................................................................................................. 5-35
Figure 5-39 Undocking Bar .................................................................................................................. 5-36
Figure 5-40 Resizing an Undocked Image ........................................................................................... 5-36
Figure 5-41 Sample Docked/Undocked Images .................................................................................. 5-37
Figure 5-42 Redocking the Graphic Display ........................................................................................ 5-37
Figure 5-43 Viewing the Graphic Display ............................................................................................. 5-38
Figure 5-44 Entering Product Length and Width .................................................................................. 5-39
Figure 5-45 Creating a Pattern ............................................................................................................. 5-39
Figure 5-46 Area Coat Program Using Graphic Display ...................................................................... 5-40
Figure 5-47 Importing an Image into a Pattern .................................................................................... 5-41
Figure 5-48 Main Pattern Displaying Both Sides of Board .................................................................. 5-42