Instruction Manual

Table of Contents vii
Figure 4-28 Needle Finder Setup Dialog Box ...................................................................................... 4-29
Figure 4-29 Production Configuration Window .................................................................................... 4-33
Figure 4-30 Product Map ..................................................................................................................... 4-35
Figure 4-31 Product Map Configuration ............................................................................................... 4-35
Figure 4-32 Maintenance Configuration Screen .................................................................................. 4-37
Figure 4-33 Adding/Deleting Maintenance Procedures ....................................................................... 4-38
Figure 4-34 Creating Custom Buttons ................................................................................................. 4-40
Figure 5-1 Opening a Product Program ............................................................................................... 5-2
Figure 5-2 Opening a Macro Program ................................................................................................. 5-3
Figure 5-3 Macro1.ECM ....................................................................................................................... 5-5
Figure 5-4 Reference Frames .............................................................................................................. 5-8
Figure 5-5 Program Properties ............................................................................................................. 5-9
Figure 5-6 Property Field Buttons ...................................................................................................... 5-10
Figure 5-7 New Program Dialog Box ................................................................................................. 5-11
Figure 5-8 Untitled Program ............................................................................................................... 5-12
Figure 5-9 Main Pattern Edit Frame Properties ................................................................................. 5-12
Figure 5-10 Applicator On/Off Button ................................................................................................... 5-13
Figure 5-11 Activating the Speed Limit ................................................................................................ 5-13
Figure 5-12 Setting the Speed Limit .................................................................................................... 5-14
Figure 5-13 Creating a Macro Program ............................................................................................... 5-15
Figure 5-14 Active Tool - Genie Camera ............................................................................................. 5-16
Figure 5-15 New Pattern Dialog Box ................................................................................................... 5-16
Figure 5-16 Verifying Pattern Position ................................................................................................. 5-17
Figure 5-17 Program Instruction Buttons ............................................................................................. 5-18
Figure 5-18 Pattern and Instruction Properties .................................................................................... 5-19
Figure 5-19 Creating the Rectangle Pattern ........................................................................................ 5-20
Figure 5-20 Creating a Mask Region ................................................................................................... 5-21
Figure 5-21 Creating a Procedure........................................................................................................ 5-22
Figure 5-22 Naming a Procedure ......................................................................................................... 5-23
Figure 5-23 Abort Program Procedure ................................................................................................. 5-23
Figure 5-24 Ini File Write Instruction .................................................................................................... 5-24
Figure 5-25 Script Instruction ............................................................................................................... 5-24
Figure 5-26 Selecting a Pattern ........................................................................................................... 5-25
Figure 5-27 Calling a Procedure .......................................................................................................... 5-26
Figure 5-28 Cropping An Image ........................................................................................................... 5-30
Figure 5-29 Zooming In ........................................................................................................................ 5-31
Figure 5-30 Zooming Out ..................................................................................................................... 5-31
Figure 5-31 Resizing an Image ............................................................................................................ 5-31
Figure 5-32 Undocking Bar .................................................................................................................. 5-32
Figure 5-33 Resizing Undocked Image ................................................................................................ 5-32
Figure 5-34 Sample Docked/Undocked Images .................................................................................. 5-32
Figure 5-35 Redocking the Graphics Display ...................................................................................... 5-33
Figure 5-36 Viewing the Graphic Display ............................................................................................. 5-34
Figure 5-37 Entering Product Length and Width .................................................................................. 5-35
Figure 5-38 Creating a Pattern ............................................................................................................. 5-35
Figure 5-39 Area Coat Program Using Graphics Display .................................................................... 5-36
Figure 5-40 Importing an Image into a Pattern .................................................................................... 5-37
Figure 5-41 Main Pattern Displaying Both Sides of Board .................................................................. 5-38
Figure 6-1 Event Monitor Error Messages ........................................................................................... 6-1
Figure 6-2 Displaying Full Text of Error Message ................................................................................ 6-1
Figure 6-3 Program Error Message ..................................................................................................... 6-2
Figure 6-4 Conditional Instruction Error Message ............................................................................... 6-3