Instruction Manual

I-2 Index
L
Light Beacon
configuration ............................................................ 4-21
beacon indicatorsettings ...................................... 4-24
log trigger fault.................................................... 4-21
Subsystem ........................................................... 4-22
Log Configuration ........................................................ 4-34
Log Files ....................................................................... 4-34
Log Trigger Fault .......................................................... 4-21
M
Macro Programs.............................................................. 5-2
creating .................................................................... 5-15
opening ...................................................................... 5-3
Main Pattern ................................................................... 5-3
Maintenance Manager .......................................... 4-37–4-39
adding procedures .................................................... 4-39
deleting procedures .................................................. 4-39
Maintenance Procedure ................................................. 5-24
creating .................................................................... 5-24
Mask Regions ................................................................. 5-4
coating inside a mask region ...................................... 5-4
creating .................................................................... 5-21
inherited mask regions ............................................... 5-4
Material Characterization ............................................... 4-8
N
Needle Finder
configuration ............................................................ 4-29
tolerances ................................................................. 4-30
O
Operator Screen ....................................................... 3-2–3-6
buttons ....................................................................... 3-5
menu bar .................................................................... 3-6
variable monitor ......................................................... 3-4
P
Pattern Array ................................................................. 5-39
Patterns ........................................................................... 5-3
creating .................................................................... 5-16
inserting instructions ................................................ 5-18
main pattern ............................................................... 5-3
placing...................................................................... 5-25
Periodic Procedures ........................................................ 5-4
Periodic Timers ............................................................. 4-32
Pneumatic Regulators and Gauges
fluid air pressure ...................................................... 3-15
Printing ......................................................................... 5-28
Procedures ...................................................................... 5-4
begin idle ................................................................... 5-6
calling ...................................................................... 5-26
creating .................................................................... 5-22
end idle................................................................ 5-6, 5-7
periodic ...................................................................... 5-4
reserved ...................................................................... 5-4
Product Frame ................................................................. 5-8
Product Map
new group ................................................................. 4-36
new part .................................................................... 4-36
Product Map Configuration .................................. 4-35–4-39
Product Programs
creating ..................................................................... 5-11
opening ....................................................................... 5-2
Production Configuration ..................................... 4-32–4-34
Program Instruction
Abort ......................................................................... B-1
Add Fault ................................................................... B-1
Arc Coat .................................................................... B-1
Arc Coat - Center Radius .......................................... B-2
Area Coat .................................................................. B-3
Call Procedure ........................................................... B-4
Check Needle ............................................................ B-5
Coat ........................................................................... B-5
Comment ................................................................... B-6
Else ............................................................................ B-6
End ............................................................................ B-6
End Flow Measurement ............................................. B-7
Fan Quick Check ....................................................... B-7
Fan Width .................................................................. B-8
Fiducial ...................................................................... B-8
Find Home ................................................................. B-9
Find Needle ............................................................... B-9
If ............................................................................ B-10
Log Message ........................................................... B-10
Move Relative ......................................................... B-10
Move Tool ............................................................... B-11
Pattern Array ........................................................... B-11
Pause ....................................................................... B-11
Place Pattern ............................................................ B-12
Position Verify ........................................................ B-12
Prompted Log .......................................................... B-12
Repeat ...................................................................... B-13
Rotate Home ............................................................ B-13
Rotate Tool .............................................................. B-14
Send ACL to Conveyor ........................................... B-14
Send ACL to Robot ................................................. B-14
Set Acceleration ...................................................... B-14
Set Outputs .............................................................. B-15
Set Velocity ............................................................. B-15
Spot ......................................................................... B-15
Terminate Program .................................................. B-16
Tilt Tool .................................................................. B-16
Wait ......................................................................... B-16
While ....................................................................... B-17
Programming
advanced concepts .................................................... 5-39
calling procedures ..................................................... 5-26
creating macro programs .......................................... 5-15
creating mask regions ............................................... 5-21
creating product programs ............................... 5-11–5-14
editing programs ....................................................... 5-27
inserting pattern instructions .................................... 5-18
placing patterns ........................................................ 5-25
Programs
running ................................................................ 5-26
macro .......................................................................... 5-2
printing ..................................................................... 5-28
product ........................................................................ 5-1