Instruction Manual
Index I-1
Index
A
Air Pressure
adjusting fluid air pressure ....................................... 3-15
AutoStart ....................................................................... 4-34
B
Bar Code Scanner
configuration .............................................................. 2-5
Bar Code/DataMatrix Scanner Configuration ............... 4-30
Bar Codes ..................................................................... 4-30
wildcard characters .................................................. 4-30
Base Frame ..................................................................... 5-8
Beacon Configuration ............................... See Light Beacon
Beacon Indicator Settings ............................................. 4-24
Begin Idle ....................................................................... 5-6
C
Camera Configuration..................................................... 4-7
Characterization .............................................................. 4-8
Characterization Sheet .................................................. 4-10
Coating Materials ............................................................ 1-3
Configuration .................................................................. 2-3
bar code scanner ......................................................... 2-5
bar code/datamatrix scanner ..................................... 4-30
beacon ...................................................................... 4-21
conveyor .................................................. 2-5, 4-17–4-18
fan width .................................................................. 4-25
fixture ....................................................................... 4-16
ID Systems ................................................................. 2-5
inverter ..................................................................... 4-19
log ............................................................................ 4-34
needle finder ............................................................ 4-29
product map .................................................... 4-35–4-39
production ....................................................... 4-32–4-34
reconfigure ................................................. 2-6–2-8, 4-31
robot ......................................................................... 4-20
system ........................................................................ 2-3
tool ...................................................................... 2-4, 4-2
Conformal Coating ......................................................... 1-2
coating materials ........................................................ 1-3
curing ......................................................................... 1-3
Conformal Coating Systems ........................................... 1-2
Conveyor
configuration ............................................ 2-5, 4-17–4-18
Creating Images ............................................................ 5-29
Cropping Images ........................................................... 5-29
Curing Systems ............................................................... 1-3
Custom Buttons ............................................................ 4-40
D
Delta Changes ............................................................... 5-39
During Idle ...................................................................... 5-6
E
ECW.INI ......................................................................... 2-3
ECXP
characterization .......................................................... 4-8
characterization wizard ............................................. 4-12
configuration .............................................................. 2-3
edit screen .......................................................... 3-7–3-13
exiting ......................................................................... 3-2
graphic display ................................................ 5-28–5-34
initial setup procedure ................................................ 2-3
installation ........................................................... 2-1–2-2
operator screen .................................................... 3-2–3-6
overview ..................................................................... 1-2
starting ........................................................................ 3-2
Edit Screen ............................................................. 3-7–3-13
opening ....................................................................... 3-7
tabs ........................................................................... 3-13
toolbar ...................................................................... 3-11
Edit Screen Menu Bar ..................................................... 3-8
Editing Programs ........................................................... 5-27
End Idle .................................................................... 5-6, 5-7
Event Monitor ................................................................. 6-1
Exiting ECXP .................................................................. 3-2
F
Fan Width
configuration ............................................................ 4-25
Fixture
configuration ............................................................ 4-16
Fixture Configuration .................................................... 4-16
Fixture Constraint Location ........................................... 4-13
Fluid Pressure
monitoring ................................................................ 3-17
Fluid Pressure Regulator and Gauge ............................. 3-15
G
Graphic Display ................................................... 5-28–5-34
Graphics Display
creating images ......................................................... 5-29
cropping images ....................................................... 5-29
importing images ...................................................... 5-29
resizing ..................................................................... 5-31
undocking/redocking ................................................ 5-31
using for programming ............................................. 5-
34
zooming .................................................................... 5-30
I
ID Systems
configuration .............................................................. 2-5
Idle Timers ............................................................. 4-32, 5-6
Importing Images .......................................................... 5-29
Installation ................................................................ 2-1–2-2
Inverter
configuration ............................................................ 4-19