User guide

I-2 Index
Main Pattern ................................................................... 5-4
Maintenance Manager.......................................... 4-30–4-32
adding procedures .................................................... 4-32
deleting procedures .................................................. 4-32
Maintenance Procedure................................................. 5-20
creating .................................................................... 5-20
Mask Regions ................................................................. 5-4
coating inside a mask region...................................... 5-4
creating .................................................................... 5-17
inherited mask regions ............................................... 5-4
Material Characterization ........................................ 4-4, 4-6
N
Needle Finder
configuration............................................................ 4-20
tolerances ................................................................. 4-21
O
Operator Screen ....................................................... 3-2–3-5
command buttons....................................................... 3-3
menu bar .................................................................... 3-5
P
Pattern Array................................................................. 5-35
Pattern Frame.................................................................. 5-9
Patterns ........................................................................... 5-3
creating .................................................................... 5-13
inserting instructions................................................ 5-14
main pattern ............................................................... 5-4
placing...................................................................... 5-21
Periodic Procedures ........................................................ 5-5
Periodic Timers............................................................. 4-25
Printing ......................................................................... 5-24
Procedures ...................................................................... 5-4
begin idle ................................................................... 5-6
calling ...................................................................... 5-22
creating .................................................................... 5-18
end idle................................................................ 5-6, 5-7
periodic ...................................................................... 5-5
reserved...................................................................... 5-4
Product Frame................................................................. 5-8
Product Map
new group ................................................................ 4-29
new part ................................................................... 4-29
Product Map Configuration ................................. 4-28–4-32
Product Programs
creating .................................................................... 5-10
opening ...................................................................... 5-2
Production Configuration .................................... 4-25–4-27
Program Instruction
Abort..........................................................................B-1
Add Fault ...................................................................B-1
Arc Coat.....................................................................B-1
Arc Coat - Center Radius ...........................................B-2
Area Coat...................................................................B-3
Call Procedure............................................................B-4
Check Needle.............................................................B-5
Coat............................................................................B-5
Comment....................................................................B-6
Else ............................................................................B-6
End.............................................................................B-6
End Flow Measurement............................................. B-7
Fan Quick Check....................................................... B-7
Fan Width.................................................................. B-8
Find Home................................................................. B-8
Find Needle ............................................................... B-9
If .............................................................................. B-9
Log Message ........................................................... B-10
Move Relative ......................................................... B-10
Move Tool............................................................... B-10
Pattern Array ........................................................... B-10
Pause ....................................................................... B-11
Place Pattern............................................................ B-11
Position Verify ........................................................ B-11
Prompted Log.......................................................... B-12
Repeat...................................................................... B-12
Rotate Home............................................................ B-12
Rotate Tool.............................................................. B-13
Send ACL to Conveyor ........................................... B-13
Send ACL to Robot ................................................. B-13
Set Acceleration ...................................................... B-13
Set Outputs .............................................................. B-14
Set Velocity............................................................. B-14
Spot ......................................................................... B-14
Terminate Program.................................................. B-15
Tilt Tool .................................................................. B-15
Wait......................................................................... B-15
While....................................................................... B-16
Programming
advanced concepts....................................................5-35
calling procedures.....................................................5-22
creating macro programs .......................................... 5-12
creating mask regions ...............................................5-17
creating product programs...............................5-10–5-11
editing programs.......................................................5-23
inserting pattern instructions .................................... 5-14
placing patterns ........................................................ 5-21
Programs
running ................................................................5-22
macro..........................................................................5-2
printing .....................................................................5-24
product........................................................................5-1
Properties ........................................................................5-9
Property List....................................................................5-9
R
Reconfigure.................................................... 2-6–2-8, 4-24
Recordkeeping.................................................................4-1
Reference Frames............................................................5-8
Robot
configuration ............................................................ 4-13
safe Z height............................................................. 4-13
Running Programs.........................................................5-22
S
Safe Z-height................................................................. 4-13
Scanner..............................................See Bar Code Scanner
Starting ECXP.................................................................3-2
Stepping ........................................................................5-35
System Configuration......................................................2-3