Instruction Manual

I-4 Index
lock out/tag out AC Power....................................... 2-12
lock out/tag out pneumatic pressure......................... 2-13
MSDS ........................................................................ 1-1
warning labels............................................................ 2-7
warning symbols ........................................................ 2-7
Safety Interlock System .........See Integrated Safety Systems
SC-104HS High Speed Film Coater ............................. 3-15
SC-105HS High Speed Film Coater ............................. 3-15
SC-200 Slim Swirl Applicator...................................... 3-17
Tri-Mode Swirl Box........................................ 1-12, 3-18
SC-204HS High Speed Film Coater ............................. 3-19
SC-205HS High Speed Film Coater ............................. 3-19
SC-300 Swirl Coat Applicator...................................... 3-20
Sensors
board ........................................................................ 1-10
board present.............................................................. 3-5
low fluid................................................................... 3-12
low solvent cup ........................................................ 3-12
SMEMA................................................................... 3-13
Setup Procedures
characterization........................................................ 6-27
coating program ....................................................... 6-27
system test................................................................ 6-28
Shutdown
extended shutdown................................................... 6-25
routine shutdown...................................................... 6-24
service shutdown...................................................... 6-25
SMEMA
defined ....................................................................... 6-2
SMEMA Connector
downstream.............................................................. 1-18
upstream................................................................... 1-18
SMEMA Sensors .......................................................... 3-13
Solvent
Low Solvent Cup Sensor.......................................... 3-12
Solvent Cups................................................................... 1-8
Specifications
conveyor .................................................................. 11-2
dispensing area......................................................... 11-3
drive system ............................................................. 11-2
facility requirements ................................................ 11-2
software.................................................................... 11-3
Standard Features............................................................ 1-3
Start Button..................................................................... 1-6
Startup.................................................................... 5-1, 6-23
Stop Button..................................................................... 1-6
Stop Pins....................................................................... 1-10
Stop/Clamp Air Gauge and Regulator .......................... 1-16
System Status Controls ................................................. 6-16
T
Teach Button................................................................. 6-15
Tensioning
cables ....................................................................... 9-11
Testing
bar code scanner....................................................... 5-17
conveyor function .................................................... 5-14
Conveyor I/O ............................................................. 5-7
flow meter ................................................................5-17
fluid pressure regulator and gauge............................ 5-10
inverter .....................................................................5-15
laser fan width control..............................................5-16
main air regulator and gauge ......................................5-8
robot function ...........................................................5-11
Robot I/O....................................................................5-5
stop/clamp air regulator and gauge.............................5-9
Tool
configuration ..............................................................7-2
defined........................................................................6-6
offset....................................................................6-6, 7-2
Tooling Plate..........................................................1-10, 3-3
Training........................................................................... 1-2
Tri-Mode Swirl Box......................................................1-12
Bead Mode ............................................................... 3-18
Monofilament Mode.................................................3-18
Swirl Mode............................................................... 3-18
Troubleshooting .............................................................. 8-3
air pressure .................................................................8-2
basic system................................................................8-1
board indexing............................................................8-3
conveyor movement ...................................................8-3
database utility..........................................................6-34
dispensing in wrong location...................................... 8-1
fluid applicator ...........................................................8-2
no power..................................................................... 8-1
no response from Control Panel .................................8-2
production statistics..................................................6-34
safety interlock ...........................................................8-2
U
Unpacking
accessories crate .........................................................4-4
dispensing system.......................................................4-4
replacement parts......................................................10-3
Upstream/Downstream SMEMA Sensors .....................3-13
V
Valve...........................................See Fluid Delivery System
Vent Air LED................................................................ 6-17
Viscosity Control System.............................................. 3-16
W
Warning Labels ............................................................... 2-7
interlock warning tag................................................2-15
Warranty........................................................................10-2
Water Trap ....................................................................1-14
emptying.....................................................................9-6
Workcell..........................................................................6-6
Workpiece ....................................................................... 6-4
Z
Z Height
safe ....................................................................6-6, 7-14
Z-Axis Controls.............................................................6-15