Instruction Manual

ManualsBrandsNordson ASYMTEK ManualsEquipmentCentury Series C-741 - Operations Manual

231

232

233

234

235

236

237

238

239

240

Index I-1

Index

Access Panels ............................................................... 10-4

Accessories Crate............................................................ 4-4

Adjustable Tooling Rails ....................................... 1-10, 3-3

Air Assist Pressure Regulator and Gauge ..................... 6-22

Air Filter ....................................................................... 1-14

Air Pressure

adjusting conveyor stop/clamp air............................ 6-20

adjusting fluid pressure ............................................ 6-21

adjusting main air..................................................... 6-19

air assist ................................................................... 6-22

Applic On/Off Button ................................................... 6-17

Bar Code Recognition System ........................................ 3-5

Bar Code Scanner

configuration............................................................ 7-15

MS810 ..................................................................... 7-15

PSC5312 .................................................................. 7-15

testing....................................................................... 5-17

utilities ..................................................................... 5-17

Board Pinning Assembly ................................................ 3-3

Board Pins ...................................................................... 1-8

Board Present Sensor...................................................... 3-5

Board Sensor................................................................. 1-10

Brush Box....................................................................... 3-5

Cable

tension reminder ...................................................... 9-11

tensioning................................................................. 9-11

Characterization..................................................... 6-27, 7-4

Characterization Sheet .................................................... 7-5

Coating Program........................................................... 6-27

Computer ...............................................1-12, 1-18, 3-3, 6-4

keyboard tray ............................................................. 1-4

monitor....................................................................... 1-4

operation .................................................................... 6-5

Configuration

bar code scanner....................................................... 7-15

beacon...................................................................... 4-19

conveyor .................................................................. 7-11

fan width control ........................................................ 7-7

fixture......................................................................... 7-8

inverter..................................................................... 7-13

reconfigure...................................................... 4-17, 7-17

robot......................................................................... 7-14

setting fixture constraint location............................... 7-8

tool............................................................................. 7-2

Conformal Coating

characterization................................................. 6-27, 7-4

curing ......................................................................... 6-1

defined ....................................................................... 6-1

setup procedures ...................................................... 6-27

system test................................................................ 6-28

Control Panel ........................................................... 1-4, 1-6

abort button.............................................................. 6-13

air assist gauge......................................................... 6-22

applic on/off button.................................................. 6-17

conveyor enable........................................................6-15

conveyor status controls ...........................................6-16

EMO...........................................................................1-6

fluid pressure gauge..................................................6-21

home button..............................................................6-15

interlock keyswitch...................................................6-16

interlock recovery..................................................... 6-16

main air LED............................................................ 6-17

motion controls......................................................... 6-15

pause button..............................................................6-13

purge button..............................................................6-17

robot enable..............................................................6-15

start and stop buttons..................................................1-6

system status controls......................................6-12, 6-16

teach button ..............................................................6-15

vent air LED............................................................. 6-17

z-axis controls .......................................................... 6-15

Conveyor

adjustments.................................................................6-8

bit mapping and functions ......................................... D-3

board pins ...................................................................1-8

chain .......................................................... 1-10, 3-3, 6-8

chain replacement..................................................... 10-5

configuration ............................................................7-11

pause button..............................................................6-16

reset button ...............................................................6-16

specifications............................................................ 11-2

stop pins ...................................................................1-10

stop/clamp air regulator and gauge........................... 6-20

testing .........................................................................5-7

utilities......................................................................5-15

Conveyor Controller Module ...............................1-12, 1-18

rear connections......................................................... D-6

replacement ............................................................ 10-14

Coordinate Systems.........................................................6-7

Daily Routine Procedures..............................................6-26

Database Utility............................................................. 6-34

Dispensing Area.....................................................1-4, 1-10

Dispensing Head .................................................. See Robot

Dispensing Process..........................................................6-2

reference frames .........................................................6-7

Dispensing System

air filter and water trap .............................................1-14

basic system troubleshooting......................................8-1

configuration and characterization .............................7-1

control panel........................................................1-4, 1-6

conveyor.................................................... See Conveyor

conveyor controller module.............................1-12, 1-18

detailed operation .......................................................6-2

dispensing area ..................................................1-4, 1-10

electrical diagrams..................................................... B-1

emergency machine off .................................... See EMO

exhaust vent duct...................................................... 1-14

facility requirements................................................. 11-2

front doors ..................................................................1-8

I/O communications .................................................. D-1

illustrated parts lists................................................... C-1

installation..................................................................4-1

interior access...........................................................10-4