www.nordictrack.com Model No. NTBE17917.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal ACTIVATE YOUR WARRANTY To register your product and activate your warranty today, go to www.nordictrackservice.com/ registration. CUSTOMER CARE For service at any time, go to www.nordictrackservice.com. Or call 1-800-TO-BE-FIT (1-800-862-3348) Mon.–Fri. 6 a.m.–6 p.m. MT Sat. 8 a.m.–12 p.m. MT Please do not contact the store.
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 PART IDENTIFICATION CHART.
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your weight bench before using your weight bench. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 1. It is the responsibility of the owner to ensure that all users of the weight bench are adequately informed of all precautions weight bench.
STANDARD SERVICE PLANS 4
BEFORE YOU BEGIN Thank you for selecting the NORDICTRACK® UTILITY BENCH weight bench. The UTILITY BENCH weight bench is designed to help you develop the major muscle groups of your upper body. Whether your goal is to tone your body, build dramatic muscle size and strength, or improve your cardiovascular system, the weight bench will help you to achieve the specific results you want. reading this manual, please see the front cover of this manual.
PART IDENTIFICATION CHART Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. Note: If a part is not in the hardware kit, check to see whether it has been preassembled. Extra hardware may be included.
ASSEMBLY • Assembly requires two persons. • To identify small parts, see page 6. • Because of its weight and size, assemble the weight bench in the location where it will be used. Make sure that there is enough clearance to walk around the weight bench as you assemble it. • In addition to the included tool(s), assembly requires the following tools: two adjustable wrenches Assembly may be easier if you have a set of wrenches. To avoid damaging parts, do not use power tools.
3. Orient the Backrest Frame (3) so that the welded tubes (A) are in the position shown. In addition, orient the Backrest Bracket (5) as shown. 3 3 Attach the Backrest Bracket (5) to the Backrest Frame (3) with four M8 x 15mm Screws (13) and four M8 Washers (18); do not fully tighten the Screws yet. 18 13 18 18 13 18 A 5 4.
5. Attach the Backrest (4) to the Backrest Frame (3) with four M8 x 15mm Screws (13) and four M8 Washers (18); start all the Screws, and then tighten them. To avoid damaging the Backrest, tighten the Screws only until the Backrest does not move or feel loose. 5 4 Note: To adjust the angle of the Backrest (4), see ADJUSTING THE BACKREST on page 11. 13 18 13 18 3 13 6. Orient the Seat Frame (6) so that the welded tubes (B) are in the position shown. In addition, orient the Seat Bracket (8) as shown.
7. Insert the end of the Seat Bracket (8) into the Frame (1), and then attach the Seat Frame (6) to the Frame with an M12 x 100mm Bolt (14), two M12 Washers (15), and an M12 Locknut (16) as shown. Do not overtighten the Locknut; the Seat Frame must pivot freely. 7 6 16 See step 6. Tighten the M8 x 15mm Screws (13). See the inset drawing. Firmly tighten the other Adjustment Knob (9) into the Frame (1) and into one of the adjustment holes in the Seat Bracket (8).
ADJUSTMENT This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 12 for important information about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for several exercises. ADJUSTING THE BACKREST To adjust the angle of the Backrest (4), firmly hold the Backrest with one hand.
EXERCISE GUIDELINES FOUR TYPES OF STRENGTH WORKOUTS workout, and the numbers of repetitions and sets to complete. Progress at your own pace and be sensitive to your body’s signals. Follow each workout with at least one day of rest. Note: A “repetition” is one complete cycle of an exercise, such as one sit-up. A “set” is a series of repetitions. Warming Up—Start with 5 to 10 minutes of stretching and light exercise.
EXERCISE LOG Make copies of this page, and use the copies to schedule and record your strength and aerobic workouts. Scheduling and recording your workouts will help you to make exercise a regular and enjoyable part of your life. Strength Date: Exercise 6. 2. 7. 3. 8. 4. 9. 5. 10. Exercise Strength Date: Exercise Time Lbs. Sets Reps 6. 2. 7. 3. 8. 4. 9. 5. 10. Exercise Strength Date: Exercise Time Lbs. Sets Reps 6. 2. 7. 3. 8. 4. 9. 5. 10.
PART LIST Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 1 1 1 1 1 1 1 1 2 2 2 4 16 Model No. NTBE17917.0 R1216A Description Key No. Qty.
EXPLODED DRAWING Model No. NTBE17917.
ORDERING REPLACEMENT PARTS To order replacement parts, please see the front cover of this manual.
