Datasheet

ManualsBrandsNordic Power ManualsExternal Plug In AdaptersPower Supply 12 ... 24 V 4.8 A/4.7 A/4.5 A/4.3 A/4.1 A/3.9 A/3.7 A/3.5 A/3.35 A/3.2 A/3.1 A/3 A

AM 09257H SWITCHING ADAPTOR SPECIFICATIONS

Ver: 1 Date: 2011-05-28

AMPLUS

AM09257 Page

SPECIFICATION

AM09257H

(output from 12Vd.c. to 24Vd.c., max. 70 watt)

SWITCHING ADAPTOR

SPECIFICATIONS

Summary of content (8 pages)

PAGE 1
SPECIFICATION AM 09257H SWITCHING ADAPTOR SPECIFICATIONS AM09257H (output from 12Vd.c. to 24Vd.c., max.
PAGE 2
SPECIFICATION AM 09257H SWITCHING ADAPTOR SPECIFICATIONS Prepared by: Checked by: Approved by: TABLE OF CONTENTS 1. SCOPE 2. SPECIFICATION NUMBER 3. ENVIRONMENTAL REQUIREMENTS 4. INPUT REQUIREMENTS 5. INTRODUCTION 6. DC INSULATION RESISTANCE 7. DIELECTRIC WITHSTAND-VOLTAGE 8. MAIN FUSE 9. INRUSH CURRENT 10. TIME SEQUENCE 11. EFFICIENCY 12. SAFETY STANDARD 13. RFI EMISSION 14. OUTPUT RATED & ELECTRICAL SPECIFICATIONS 15. RELIABILITY 16. OUTLOOK DRAWING 17. NAME PLATE 18.
PAGE 3
SPECIFICATION AM 09257H SWITCHING ADAPTOR SPECIFICATIONS 1. SCOPE This document is applied to AM09257H model for S.M.P.S 2. SPECIFICATION NUMBER AMPLUS part number : Customer part number : AM09257H 3. ENVIRONMENTAL REQUIREMENTS Operating temperature: 0 -- 40 Storage temperature :-25 -- +85 Operating humidity : 30% -- 95% Storage humidity : 30% --98% Operating bar : 1BAR 4.
PAGE 4
SPECIFICATION AM 09257H SWITCHING ADAPTOR SPECIFICATIONS The S.M.P.S will shut down automatically when the AC input voltage lower than AC 90 V. The S.M.P.S output voltage will drop to very low when overload by overload protection. The S.M.P.S should not be fired or emitted smoke by protection when the circuit is short. The S.M.P.S will shut down automatically when output voltage is over 28.5V by overvoltage protection. The S.M.P.
PAGE 5
SPECIFICATION AM 09257H SWITCHING ADAPTOR SPECIFICATIONS 11. EFFICIENCY The efficiency of the S.M.P.S must be satisfied the minimum 87%. 12. SAFETY STANDARD To meet ETL-UL1950,CETL-C22.2 NO.950, GS-DIN EN60950 AS/NZS 4665.1 : 2005, EuP 2005/32/EC 13. RFI EMISSION EN55022: 2006+A1 EN61000-3-2: 2000 EN61000-3-3: 1995+A1 EN55024: 1998+A1+A2 FCC PART 15 14. OUTPUT RATED & ELECTRICAL SPECIFICATIONS RATED OUTPUT (V) 12 13 14 15 16 17 18 19 20 21 22 23 24 Rated current(A) 5.0 4.8 4.7 4.5 4.
PAGE 6
SPECIFICATION AM 09257H SWITCHING ADAPTOR SPECIFICATIONS 15. RELIABILITY TESTING A. DC OUTPUT CORD PUSH/PULL TEST OF I/O CONECTOR SIDE Test condition: 8kgf X10sec at Y axis; 5kgfX10sec at other 4 direction verticality RESULT: No cutting inner wire is acceptable 5kgfx10s 8kgfx10s 5kgfx10s 5kgfx10s 5kgfx10s B. DC OUTPUT CORD PUSH/PULL TEST OF ADAPTOR SIDE Test condition: 8kgf X10sec at 5 direction verticality RESULT: No cutting inner wire is acceptable C.
PAGE 7
SPECIFICATION AM 09257H SWITCHING ADAPTOR SPECIFICATIONS E. INDIVIDUAL DROP TEST Test condition: 6 face, each face 1 time 70 cm, on the 5mm wooden board. RESULT: Without opening of case and crack, etc. electric characteristic shall be satisfied.light crack after test is acceptable. F. LOW TEMPERATURE STORAGE TEST Keep on -30 (Packing) for 168 hours, and check the action after 3 hours in 25 . RESULT: All normal function and meet specification. G.
PAGE 8
SPECIFICATION AM 09257H SWITCHING ADAPTOR SPECIFICATIONS 16.