Installation Instructions

ManualsBrandsNordic Plow ManualsOutdoors48" Universal ATV Snowplow

Nordic Auto Plow LLC

771 W. North Ave.

West Chicago IL 60185

Phone for customer service: 888-662-PLOW (7569)

E-mail: support@nordicautoplow.com

Website: nordicautoplow.com

866-941-6577 (Fax)

UNIVERSAL LIGHT WEIGHT PLOW - ATV/QUAD

ASSEMBLY INSTRUCTIONS

PLOW ASSEMBLY Steps:

1 2 3

5 6

ATV ADAPTER ASSEMBLY Steps:

8 9A9

PLOW ATTACHMENT TO ATV Steps:

10 11

ANGLE PLOWING ADJUSTMENTS Step:

Summary of content (8 pages)

PAGE 1
UNIVERSAL LIGHT WEIGHT PLOW - ATV/QUAD ASSEMBLY INSTRUCTIONS PLOW ASSEMBLY Steps: 1 2 3 ATV ADAPTER ASSEMBLY Steps: 8 9 9A PLOW ATTACHMENT TO ATV Steps: 10 11 ANGLE PLOWING ADJUSTMENTS Step: 4 12 Nordic Auto Plow LLC 771 W. North Ave. West Chicago IL 60185 Phone for customer service: 888-662-PLOW (7569) E-mail: support@nordicautoplow.com Website: nordicautoplow.
PAGE 2
PLOW ASSEMBLY PARTS: TOP PIVOT PLATE (1 - PIECE) BLADE END CAP (2 - PIECES) BLADE SECTION (3 - PIECES) BOTTOM PIVOT PLATE (1 - PIECE) BLADE CHANNEL (2 - PIECES) BLOCK (8 - PIECES) PLOW STRAP (1 - PIECE) ATV ADAPTER ASSEMBLY PARTS: CLAMP BRACKET (4 - PIECES) BELLY PLATE (1 - PIECE) BELLY U-BRACKET (1 - PIECE) CLAMP PLATE (1 - PIECE) BOOT PLATE (2 - PIECES) PIVOT BRACKET (1 - PIECE) AXLE (1 - PIECE) HARDWARE: USE FOR PLOW ASSEMBLY: USE FOR ADAPTER AND PLOW ATTACHMENT: STEP - 10 ONLY T-HANDLE Q
PAGE 3
IMPORTANT! TIGHTEN FULLY 1 1” LONG X4 A TAB LOCKING FACES OF LOCK NUTS MUST ALWAYS BE IN AGAINST THE SURFACE YOU ARE FASTENING! A A A A Place the Blade Sections face down and slide together as shown. A - Feed 1” long bolts through 4 - fastening points. Attach washers and nuts, then finger tighten only. Align Blade Sections and tighten fully. 2 3” LONG WASHERS X4 IMPORTANT! TIGHTEN FULLY Feed 3” long bolts through (2) holes in each End Cap and Blade Section.
PAGE 4
NOTE: SLOT ON TOP OF PLOW 5 BLADE CHANNEL (SMALL FLANGE UP) Slide a Blade Channel (smaller flange at the top) over the top (4) protruding bolt ends. Secure parts with (4) Keps nuts as shown. 6 BLADE CHANNEL (SMALL FLANGE DOWN) Slide a Blade Channel (smaller flange at the BOTTOM) over the bottom (4) protruding bolt ends. Secure parts with (4) Keps nuts as shown.
PAGE 5
8 BELLY PLATE The Belly Plate attaches to the underside of the ATV frame as shown. BELLY PLATE 2” BOLTS LOCKING FACES OF LOCK NUTS MUST ALWAYS BE IN AGAINST THE SURFACE YOU ARE FASTENING! ATV FRAME MEMBERS CLAMP PLATE CLAMP BRACKET CLAMP PLATE 1” BOLTS BELLY PLATE LOCK NUTS BELLY PLATE The above view shows how Adapter Assembly Parts are used to secure the Belly Plate to a typical ATV frame. Where clearances do not allow use of the Clamp Plate, Use (2) additional Clamp Brackets (supplied) instead.
PAGE 6
BOOT PLATE BOOT PLATE AXLE HOLE 9 AXLE HOLE BELLY U-BRACKET BOOT PLATE Loosely assemble these parts only by finger tightening nuts and 1” bolts. Place loosely assembled parts on the belly plate as shown in step - 9a below. Arrange parts so the axle holes are 7” above the ground.
PAGE 7
PIVOT BRACKET 10 For the (2) holes closest to the ATV: Use the 1/2” x 1’ long bolts, nylon insert lock nuts, with washers positioned as shown, and secure from underneath as shown. Do not tighten fully, but allow parts to pivot freely. PIVOT PLATES ATTACHED TO PLOW 11 2” A 7” A AXLE PLOW BLADE SIDE VIEW Feed the Axle through the holes in the Pivot Bracket which will allow the top edge of the plow to be 2” BACK FROM THE BOTTOM EDGE as shown in the above.
PAGE 8
DISCHARGE TO LEFT DISCHARGE TO RIGHT STRAIGHT PLOWING 12 T-HANDLE QUICK RELEASE PINS PLOWING ANGLE SETTINGS ARE SHOWN ABOVE. For plow discharging to the LEFT or RIGHT of the operator rotate the plow as shown, line up holes in the Pivot Brackets with the hole in the Pivot Plate, feed T - Handle Quick Release Pins through the appropriate holes. 13 STRAP Feed the Strap through the small slot at the top of the plow.