Spray Height Control System UC4+ Severe Terrain Option Installation Manual Improving the competitiveness of Industry and Agriculture through Precision Measurement
Printed in Canada Copyright 2010 by NORAC Systems International Inc. Reorder P/N: 4465BC+INST Rev A (UC4+ Severe Terrain Option) NOTICE NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.
TABLE OF CONTENTS 1 INTRODUCTION .................................................................................................................................................. 1 2 GENERAL SYSTEM DESCRIPTION ................................................................................................................... 2 3 PARTS LISTS..........................................................................................................................................................
1 INTRODUCTION This kit provides the necessary parts that will add the severe terrain option to your sprayer. These parts integrate into your existing NORAC UC4+ Sprayer Height Control System for minimal setup of this feature. Please take the time to read this manual completely before attempting to install the system. A thorough understanding of this manual will ensure that you receive the maximum benefit from the system.
2 GENERAL SYSTEM DESCRIPTION Figure 1 depicts the general system layout of the UC4+ Spray Height Control system. Figure 1: System Components and General Location NOTICE: Every effort has been made to ensure the accuracy of the information contained in this manual. All parts supplied are selected specially to fit the sprayer to facilitate a complete installation. However, NORAC cannot guarantee all parts fit as intended due to the variations of the sprayer by the manufacturer.
3 PARTS LISTS The parts that come with your UC4+ Spray Height Control System are listed in Table 1. The item number on the left side of this table references each part. Please ensure that all parts in your kit are present before proceeding with your installation. Table 1:Severe Terrain Option Parts Item Part Number Name Quantity B05 44706-01 KIT CABLE TIE BLACK 10 PCS 21 IN 150 PCS 7.
The parts that come with your Severe Terrain Option kit are shown below in their general installation configuration.
4 INSTALLATION PROCEDURE 4.1 SENSOR INSTALLATION 1. Assemble the Breakaway Sensor Mounting Brackets (B11) as show in Figure 3 and Figure 4. c) Place the collar onto the angled tube of the mounting base. d) Install the spring between the collar and the upper ring of the base. e) Insert tube through assembly and tighten the collar 2. Mount the sensor brackets onto the boom half way between the tip and center of the sprayer (Figure 8).
General mounting rules ultrasonic wing sensors: for UC4+ a) In its lowest position, the sensor mouth must be 9 inches or more from the ground. b) The bottom of the sensor must be at least 9 inches in front of the spray nozzles. c) The bottom of the sensor must be at least 9 inches above the spray nozzles. Figure 5: An Acceptable Mounting Avoid mounting sensors in locations where they may read from parts of the boom as shown in Figure 6.
Figure 8: Sensor Serial Number Installation Location * Existing Parts * New Parts 7
4.2 ELECTRICAL INSTALLATION 1. Disconnect the existing cable C02B from the existing cable C02. 2. Connect cable C02B included in this kit between the cables as shown in Figure 9. 3. Route the free ends of cable C02B to the new sensors and connect to the sensor connectors. 4. Cable tie all cables to existing hoses or cables. It is recommended to follow existing cables or hoses when routing the cables.
4.3 COMPLETING THE INSTALLATION 1. Start up your sprayer and test the sprayer’s functionality. The NORAC Control Panel does not need to be powered up for the original switches to function. Unfold the booms and raise/lower each boom and main section. Again confirm that the cabling/hoses are agreeable to the entire range of motion. 2. If any functions do not work, review the hydraulic and electrical portions of this manual to check for proper installation.
5 ELECTRICAL REFERENCE – CABLE DRAWINGS 5.
www.norac.ca Canada NORAC Systems International Inc. CALL TOLL FREE: 1-800-667-3921 (306)664-6711 SHIPPING ADDRESS: 3702 Kinnear Place Saskatoon, SK S7P 0A6 United States NORAC, Inc.
